Manual Settings - TFA 35.1134 Mode D'emploi

TFA_No. 35.1134_Anleitung_03_20
MULTY - Wireless weather station
7. Note for radio-controlled time DCF
The time base for the radio-controlled time is a caesium atomic clock operated by
the Physikalisch Technische Bundesanstalt Braunschweig. It has a time deviation of
less than one second in one million years. The time is coded and transmitted from
Mainflingen near Frankfurt via frequency signal DCF-77 (77.5 kHz) and has a trans-
mitting range of approximately 1,500 km. Your radio-controlled clock receives this
signal and converts it to show the precise time. Changeover from summer time or
winter time is automatic. In Daylight Saving Time "DST" is shown on the LCD. The
quality of the reception depends mainly on the geographic location. Normally there
should be no reception problems within a 1,500 km radius around Frankfurt.
Please take note of the following:
• The recommended distance to any interfering sources like computer monitors or
TV sets is at least 1.5 - 2 meters.
• Inside ferro-concrete rooms (basements, superstructures), the received signal is
naturally weakened. In extreme cases, please place the unit close to a window to
improve the reception.
• During nighttime, the atmospheric interference is usually less severe and recep-
tion is possible in most cases. A single daily reception is adequate to keep the
accuracy deviation under 1 second.
8. Operation
• Important: During the reception of the outdoor values and the radio-controlled
time, a button operation is not possible.
• Press and hold the UP or DOWN button in the respective setting mode for fast
running.
• The device will automatically quit the setting mode if no button is pressed within
30 seconds.

8.1 Manual settings

• Press and hold the MODE button in normal mode. The year digit (2011 YR -
default) will be flashing. Press the UP or DOWN to adjust the year.
• Press the MODE button to make the settings in the following sequence: the
month, the day, the day-of-week language (GE - default), the time zone (00 -
default), the 12 or 24 hours system (24 H - default), the hours and the minutes.
Press the UP or DOWN button to adjust it.
• Confirm with the MODE button.
• The manually set time will be overwritten by the DCF time when the signal is
received successfully.
8.1.1 Setting of the 12 and 24 hours display
• In the 12 HR system AM or PM (after 12 o'clock) appears on the display.
• Press the UP or DOWN button in the setting mode to choose the 12 HR or 24 HR
system.
8.1.2 Setting of the time zone
• In the setting mode you can make the time zone correction (-12/+12).
• The time zone correction is needed for countries where the DCF signal can be
received but the time zone is different from the DCF time (e.g. +1=one hour later).
• ZONE appears on the display.
• Press the UP or DOWN button.
• Confirm the setting with the MODE button.
18
17.03.2020 18:04 Uhr Seite 10
MULTY - Wireless weather station
8.1.3 Setting of the language of the day-of-the week
• In the setting mode you can make the setting of the day-of-the week language:
German (GE), Italian (IT), French (FR), Dutch (NE), Spanish (ES), Danish (DA) and
English (EN).
8.2 Setting of the alarm time
• Press the ALARM button.
• AL and 7:00 (default) or the last adjusted alarm time appear on the display.
• Press and hold the ALARM button.
• The alarm symbol appears on the display and the hour digit will be flashing.
• Press the UP or DOWN button to adjust the hours.
• Press the ALARM button again and you can adjust the minutes with the UP or
DOWN button.
• Confirm the setting with the ALARM button. The alarm is activated.
• Press the ALARM button again.
• The display shows the current time.
• When the adjusted alarm time is reached, the alarm will ring.
• The alarm symbol will be flashing.
• Press any button and the alarm will stop.
• If the alarm is not stopped manually, the increasing alarm will automatically turn
off after certain minutes and will be reactivated at the same time.
• When the alarm rings, press the SNOOZE-LIGHT button and the snooze function
will be activated.
• Once the snooze function is activated, Zz will be flashing on the display.
• The alarm will be interrupted for 5 minutes.
8.2.1 Activate and deactivate the alarm function
• Press the MODE button in normal mode, to turn off the snooze function.
• Press the MODE button again in normal mode, to deactivate the alarm function.
• The alarm symbol and the snooze symbol disappear on the display.
• Press the MODE button in normal mode, to activate the alarm function again.
• The alarm symbol appears on the display.
8.3 Backlight
• Press the SNOOZE-LIGHT button to activate the backlight for few seconds.
8.4 Weather forecast symbols
• The weather station has four different weather symbols (sunny, slightly cloudy,
cloudy, rainy).
• The weather symbol is based on the changes of temperature and humidity values
of channel 1.
9. Moon phase
• The moon phase of each day is shown on the display.
A B C D
A: New Moon D: Waxing Gibbous
B: Waxing Crescent E: Full Moon
C: First Quarter F: Waning Gibbous
E F G H
G: Last Quarter
H: Waning Crescent
19