Quick A 312 Manuel De L'utilisateur page 17

POS. DESCRIPTION
8 Screw for pressure lever
9A Black pressure lever
9B White pressure lever
10 Spring for pressure lever
11 Rider base
12 Rope/chain stripper R base
13 Rider screw
14 Gasket / Rider jig
15A Studs Aries base
15B Studs Flair base
16A Gearbox 500W
16B Gearbox 500W - Hi Speed
17 Washer
18 Spring washer
19 Nut
20 Nut
21 Paper gasket
22 Key
23A Electric motor 300W 12V
23B Electric motor 500W 12V
23C Electric motor 500W 24V
24 Flange gasket 500W
25 Watertight 500W
26 Poles gasket 500W
27 Bottom protec cover 500W
28 Screw
29 Key
30 Short shaft
31 Long shaft
32 Key
33 Key
34 External circlip
35 Bearing
36 Internal circlip
37 Oil seal
38 Ring
39 Clutch cone
40 Magnet
41A Gypsy
41B Gypsy 1/4" - complet
42 Gypsy cover
43 Drum
44 Bush
45 Handle
AFR 300/500W - REV009C
CODE
MSMVT0400000
PDLVTD040000
PDLVTD04W000
Quick
MMTND0400000
to marine environments. In any case, any salt deposits on
SGMSC04C0000
the outside must be removed periodically to avoid corrosion
MSN04CX00000
and damage to the equipment. The parts where salt may
MBV0616MXTSC
have built up should be washed thoroughly with fresh water.
PGBSC0400000
MBP080607X00
Once a year, the drum and the gypsy are to be taken apart
MBP080608X00
as follows:
MR0400000000
MR05AFHS0000
DRUM VERSION
MBR08X000000
Use the handle (45) to loosen the bush (44); pull off the drum
MBR08XDE0000
(43) and the top clutch cone (39); loosen the fixing screws (2
MBD08MXEN000
or 13) of the rope/chain stripper (3 or 12) and remove it. Pull
MBV0516MXE00
off the gypsy (41).
PGBMR0400000
MBH040415F00
NO-DRUM VERSION
EMF031200000
Use the handle (45) to remove the gypsy cover (42); remove
EMF051200000
the top clutch cone (39); loosen the fixing screws (2 or 13) of
EMF052400000
the rope/chain stripper (3 or 12) and remove it and pull off
PGGPMFN04000
the gypsy (41).
PCCCPM040000
PGGPMPM04000
Clean all the parts removed to avoid corrosion, and grease
PCCPPMFN0400
the shaft thread (30 and 31) and the gypsy (41) where
MBV03916AXCC
the clutch cones rest (use grease suitable for marine
MBH0606050X0
environment) (39).
MSAS04203R30
MSAS04245R30
Periodically grease the hinge pin (7) of the inspection door
(only windlasses with aluminium bases).
MBH0606025X0
MBH0606060X0
Remove any oxide deposits from the terminals of the
MBAE1715Y000
electric motor and the reversing solenoid unit; grease them.
MBJ60032RS10
MBAN3515Y000
PGPRL1735700
MBAC1720Y000
MSF04R100000
KPMC08060000
ZSB040600000
ZSB040140000
MSGB04000R01
MSE040000R02
MSD040000R01
PVLVSDN00000
MAINTENANCE
WARNING: make sure the electrical power to the
motor is switched off when working manually on the
windlass. Carefully remove the chain or rope from the
gypsy or the rope from the drum.
® windlasses are manufactured with materials resistant
GB
17