Peg-Perego kit auto culla elite Notice D'emploi page 13

• Before use make sure that all of the attachment
mechanisms are connected properly.
• Do not insert fingers into the mechanisms.
• Do not use near heat sources, open flames or dangerous
objects that are within reach of the child.
• It could be dangerous to use accessories which are not
approved by the manufacturer.
• Make sure the belts fastening the Car bassinet unit to the
vehicle are always taut and adjust the straps securing the
child.
• Never twist the belts.
• Replace the item if it undergoes significant strain in an
accident or shows clear signs of breakage or deformation.
• The safety device should not be modified by users in any
circumstances.
• Do not use in vehicles with the backrest in the raised
position.
• Carefully follow the instructions supplied by the
manufacturer of the child restraint system.
• Never leave a child alone and unsupervised in a car, not
even for a short time. The temperature inside the vehicle
can change rapidly and become dangerous for the child
inside.
• If using a second-hand product, make sure it is a recent
model, comes with instructions, and is fully functional in
all parts. An obsolete product may not conform to safety
standards, due to natural ageing of materials and updating
of regulations. If you have any doubts, contact the
manufacturer's customer service centre.
• Do not remove or change the white polystyrene part to
the sides of the bassinet as this is an important safety
element.
• Do not use the Culla Elite if it has broken or missing parts
or if it has been subjected to violent stress in an accident,
as it may have suffered structural damage that is not visible
yet extremely dangerous.
• The Car bassinet unit must always be secured with the
vehicle's safety belts, even when the child is not present. In
the event of sudden braking, it could injure the occupants
of the vehicle.
• When travelling in vehicles, never hold the child in your
arms and never put him/her anywhere but in the Car
bassinet unit. In the event of sudden braking, even at low
speeds, the child would be flung forward.
• Take particular care to make sure that luggage or other
objects are not located where they may injure the child in
the Car bassinet unit in the event of an accident.
• Do not leave the Car bassinet unit in vehicles exposed to
the sun. Some parts might heat up and be harmful to the
delicate skin of the child – check before placing the child
in the seat.
• Make sure that the Car bassinet unit is not obstructed by any
moving parts of the vehicle's seat or by one of the doors.
• Do not use the Car bassinet unit without its fabric covering,
which cannot be replaced with one not approved by the
manufacturer since it is an integral part of the Car bassinet
unit and the safety system. If replacing it, use an official
spare part.
• Culla Elite was designed for use with the polystyrene
shock absorber supplied with the "CULLA ELITE CAR KIT".
For correct installation, follow the instructions in this user
manual.
WARNING: do not remove when the Culla Elite is being
used in the car.
• Take care when adjusting the mechanisms (handle,
backrest) with the child present.
Instructions for use
Car Kit
How to fit the safety harness
IMPORTANT: during car travel, our mattress with a
3-point harness can be used.
IMPORTANT: In vehicles, always keep the backrest in
the horizontal position.
1 Unbutton the hood and foot muff (if present) completely
(fig_a) and remove them both (fig_b). Raise the backrest and
pull out the mattress (fig_c). Open the two zips and remove
the inner lining (fig_d).
2 Insert the 4 polystyrene sections inside the Culla Elite, and
position them as shown in the figure.
WARNING: every piece must be inserted in its position
and cannot be replaced by another. Do not force the
pieces into place to avoid breaking the polystyrene.
3 Place the inner lining back into position, fitting the base over
the backrest.
4 Insert the mattress, which comes with 3 belt openings, and
fit it over the backrest.
13