Instructions To The Owner; Safety Instructions; Assembly Instruction; Basic Instruction For Operation - IRT Hyperion IRT 4-1 PcAuto Mode D'emploi

IRT 4-1 PcAuto, IRT 4-2 PcAuto, IRT 4-10 PcAuto and IRT 4-20 PcAuto
3.

Instructions to the owner

The owner of the dryer must produce clear operating instruc-
tions, adapted to local site conditions, and make these
available to all users who have to observe these operating
instructions.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabili-
ties, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Dispose of used items at the nearest environmental protec-
tion facility for recycling.
For safety reasons the infrared dryer must be supplied by
recommended maximum fuse, see tables in chapter 2.2.
4.

Safety instructions

The mobile dryer must not be exposed to paint fog, sanding
dust or solvents, due to fi re hazard. Furthermore, this will
reduce the lifetime of the dryer. Allow for suffi cient cool-
ing time of the dryer. The distance to the object that is to
be dried must be suffi cient. Otherwise there is risk for fi re
or explosion! Keep all fl ammable materials in a suffi cient
distance from the hot surfaces of the dryer.
4.1 Hazards
Tilting
The risk for tilting increases when the arm is located in an
upright position. Turning both cassettes to one side also
increases the risk for tilting.
Fire and explosion.
Do not store, prepare or use solvent-containing materials
within a 5 m/16 feet radius of the mobile dryer. Flammable
materials should not be placed close to a drying device in use.
With the temperature control turned off, the temperature
might raise quickly and the risk for fi re increases, especially
if you have a distance less than 60 cm/24" to the object.
Never direct the cassette towards highly combustible materi-
als.
Electrical equipment
The mobile dryer is operated with high electrical voltage,
which can be highly dangerous.
Before accessing live parts, remove the main connector from
the wall socket. Only professional electricians may have
direct access to the electrical components.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualifi ed persons
in order to avoid a hazard.
WARNING !
Intensive heat radiation. Hands, face
and other parts of the body should be
4 exposed as little as possible to the heat
radiation.
5.

Assembly instruction

See separate document for detailed instructions.
For mobile dryers:
713847 IRT Pc Mobile Assembly Manual
For rail systems:
713683 IRT 3-20_4-20 Rail System Assembly Instruction
6.

Basic instruction for operation

6.1 Keyboard
Software defi ned button
Confi rmation choices
Start
Stop
Cassettes in use
)
(one or two
6.2 Display
Active program
Flash off – active
Full bake – inactive
Confi rmation choices
6.3 Program mode – General rules for navigation
in the software
6.4 Program mode
This mode is for your everyday use. It helps you run the dryer
with preinstalled programs and edit program settings.
When you start the dryer, an information screen will appear
for two seconds. By pressing the confi rmation or cancella-
tion button this information will show until released. The
diagram shows cassette fi lter usage and notifi es when it's
time to change fi lter. To replace fi lter see chapter "11.1
Filter replacement".
6.5 Settings mode
The Settings mode enables you to change advanced system
parameters. Thanks to our advanced control system in this
mobile dryer there are many settings that can be altered.
This is normally not a part of the everyday usage.
To enter the settings mode press both arrow keys when you
turn the main switch to position 1.
For further information see Chapter 9
Software defi ned button
Cancellation choices
Enter
Temperature control
(on/off)
One cassette active
Temperature reading
Cancellation choices
To enter the program mode, turn the
main switch on.
713687 rev 5