Intended Use Of The Product; Product Description; Particular Advantages; Technical Data - IRT Hyperion IRT 4-1 PcAuto Mode D'emploi

1.

Intended use of the product

This product serves exclusively to accelerate the drying/curing of
putty, fi ller, base and clear coats. This applies to both water-borne
and solvent-based products. It´s site of use is the preparation area
and fi nishing area. Within the automotive industry and vehicle
repair sectors, it is used to cure small areas before polishing. The
product must not be used for other purposes than the described
drying processes. The maximum ambient temperature during opera-
tion should not exceed 40°C. The IRT 4-1 PcAuto and IRT 4-2 PcAuto
dryers must not be used in spray booths or within a distance of 5m from
spraying activities in order to avoid explosion risk. This prohibition is also
valid for the IRT 4-20 PcAuto & IRT 4-10 PcAuto, if not combined with
the IRT Dust Cover and Surveillance System (document 714147).
2.

Product description

The dryer is an essential aid for paint repair on small and medium
sized areas.
The easily manoeuvrable IRT 4-1 Pc Auto, 4-2 Pc Auto 4-10 PcAuto
and 4-20 Pc Auto is equipped with one or two compact cassettes.
Each cassette is equipped with four Infra Red (IR) lamps with gold
plated free-form refl ectors and a ventilator. The design, combined
with a gas spring, makes positioning of the cassette simple. The
IR lamps are easily exchangeable and the refl ectors are protected
against mechanical damage by a mesh. The dryer has a selection of
sophisticated programs.
2.1

Particular advantages

2.1.1 Higher quality
Using the dryer when you cure putty also improves th e quality of
the top coat.
The short wave IR curing enables the coating to be cured from the
inside outwards. This prevents solvents to be trapped inside the
coating and ensures a fast and high quality curing.
2.1.2 Short drying times
for 60 cm distance
material
Putty
Filler
Primer
Water base
Base coat
Top coat
Clear coat
Filler on plastics
Top coat on plastics
Clear coat on plastics
2.1.3 Regulated temperature
The dryer has a pyrometer which carefully controls tempera-
ture of the object. The computer does not only measure the
maximum allowed temperature but also the temperature
raise. It ensures that the programmed drying/curing tem-
perature is maintained, thereby achieving optimum curing,
without risk for "over burning".
713687 rev 5
IRT 4-1 PcAuto, IRT 4-2 PcAuto, IRT 4-10 PcAuto and IRT 4-20 PcAuto
minutes
2– 3
3– 7
5– 8
2– 4
4– 8
6–10
5–10
7–10
15–18
15–18
2.1.4 Hi-tech shape of refl ectors with short wave IR
By using short-wave technology and gold-coated refl ectors with
a high tech shape important advantages are achieved. Firstly, by
radiating only the needed areas and not heating any air, a lower
energy consumption is achieved. Secondly, a more uniform surface
temperature is obtained by distributing the energy evenly. Thirdly,
a larger drying surface is achieved. Fourthly, less radiation outside
the curing area.
2.2

Technical data

All dryers emit short wave radiation with a peak at 1120 nm. The
fi gures below show the maximum drying area, when the respective
dryer is used in 60 cm distance from a black sheet metal.
1,1 m
Voltage 220–240 V220–240 V 380–420
1 Ph/PE 3 Ph/PE
Frequency 50–60 Hz50–60 Hz
Current 26 A 15 A
Power 6 kW 6 kW
Fuse**
4-1 PcA 30 A* 16 A*
4-10 PcA n/a Max 100A Max 100A
o
Drying temp. Max 170 Max 170
Noise level <70 dB(A)<70 dB(A) <70 dB(A) <70 dB(A) <70 dB(A)
2,2 m
Voltage 220–240 V220–240 V 380–420 V 440–480 V 480 V
1 Ph/PE 3 Ph/PE
Frequency 50–60 Hz 50–60 Hz 50–60 Hz
Current
4-2 PcA 48 A 27 A
4-20 PcA n/a 30 A
Power 12 kW 12 kW
Fuse**
4-2 PcA 50 A* 32 A*
4-20 PcA n/a Max 100 A Max 100 A Max 100 A --
Drying temp. Max 170 o Max 170
Noise level <70 dB(A) <70 dB(A) <70 dB(A) <70 dB(A) <70 dB(A)
* MCB (Minature Circuit Breaker) type C or D. Normal fuse type slow.
** The dryer shall be operated with a fuse of the recommended rating.
Weight, dimensions and product identity label on last page.
IRT 4-1 PcAuto
IRT 4-10 PcAuto
drying surface
440–480 V 480 v
3 Ph/PE 3 Ph/PE 2 Ph/PE
50–60 Hz 50–60 Hz 50–60 Hz
9 A 9 A 13 A
6 kW 6 kW 6 kW
10 A* 20 A 20 A
Max 100A Max 100A
o o o
Max 170 Max 170 Max 170
IRT 4-2 PcAuto
IRT 4-20 PcAuto
drying surface
3 Ph/PE 3 Ph/PE 2 Ph/PE
50–60 Hz 50–60 Hz
16 A 16A 26A
17 A 17 A --
12 kW 12 kW 12 kW
16 A* 20 A 32 A
o Max 170 o Max 170 o Max 170
o
o
3