Before The First Use - Domo DO7293S Mode D'emploi

Product Operation

BEFORE THE FIRST USE

Battery Charging
· Put two AAA batteries in the remote control.
· Set the time (see "use/use without remote control/plan: clock").
1. Charging Station Placement
· Prior to initial use, charge the robot vacuum cleaner for 5 hours (see "use/charging").
A. Place charging station against the wall,
· Place the signed brushes on the vacuum cleaner. Press on them until you hear a click. The brushes and
and remove obstacles about 1m on either
the machine are marked with L (left) and R (right); make sure they match.
Product Operation
sides and 2m in front of the station. Please
remove obstacles as show in the right figure.
INSTALLING THE CHARGING STATION
Battery Charging
B. If robot is power off, switch on the robot first before charging.
1. Place the charging station on a smooth hard surface, e.g.
1. Charging Station Placement
tiles, parquet, short-haired sturdy carpet, against a wall or
Charge the robot in either way as shown below:
2.
A. Place charging station against the wall,
cupboard.
A. Plug one end of the adapter into the robot and the other end into the power socket as shown
2. Make sure that there is an area of at least 1 m free on the
and remove obstacles about 1m on either
in Fig a.
left and right sides of the charging station. In front of the
sides and 2m in front of the station. Please
B. Press the "HOME" button on the remote control or robot to operate the robot looking for the
charging station, there must be a free area of 2 m (Fig. 1).
remove obstacles as show in the right figure.
charging docking automatically as shown in Fig b.
If this is not the case, it is possible that the vacuum cleaner
B. If robot is power off, switch on the robot first before charging.
cannot find the charger when it must charge.
3. Take the adapter, put the plug in the outlet and put the DC
Charge the robot in either way as shown below:
2.
plug into the charging station (Fig. 2).
A. Plug one end of the adapter into the robot and the other end into the power socket as shown
in Fig a.
IMPORTANT: always make sure that no cables are in front of or
B. Press the "HOME" button on the remote control or robot to operate the robot looking for the
next to the charging station; these could get caught between
charging docking automatically as shown in Fig b.
the wheels or brushes of the vacuum cleaner.
USE
Turn the machine on with the on switch on the side of the appliance prior to use or charging.
Note:
STANDBY/SLEEP MODE/OFF
a. When robot is in charging, the LED panel will gradually show "1111" from left to right.
Standby
b. When charging is over, the LED panel will show "FULL".
The machine is in standby mode when the on switch is on and the machine is in idle state, ready to be
c. In standby status, the robot will
used immediately.
d. In working status, the robot will look for the charging dock automatically when the battery
Sleep mode
level is low.
When the machine is in sleep mode, you must first activate it before you can start the machine. This is
In Order to Extend Battery's Life
done by pressing the on/off touchscreen button on the machine or with the ON/OFF button on the remote
Note:
a. Please charge the robot for up to 5 hours during the first charging.
control.
a. When robot is in charging, the LED panel will gradually show "1111" from left to right.
b. Charge the robot as soon as possible when battery capacity is low.
The machine automatically goes into sleep mode after being in standby mode for 15 minutes. You can also
b. When charging is over, the LED panel will show "FULL".
c. The robot will return to the charging dock automatically when cleaning is finished or battery
turn on the mode yourself by pressing and holding the on/off touchscreen button on the machine for 3
c. In standby status, the robot will
capacity is low.
seconds.
d. When you do not use the robot for some time, please fully charge the battery first, then
d. In working status, the robot will look for the charging dock automatically when the battery
switch off the robot and keep it in a cool but dry place.
Off
level is low. e. If the robot has been put aside over 3 months, please charge the robot for 5 hours first
You can turn off the machine completely by switching off the on switch on the side of the device while in
In Order to Extend Battery's Life
before using it for cleaning.
standby mode.
a. Please charge the robot for up to 5 hours during the first charging.
The machine turns itself off after being in sleep mode for 15 minutes if no timer has been set.
b. Charge the robot as soon as possible when battery capacity is low.
c. The robot will return to the charging dock automatically when cleaning is finished or battery
capacity is low.
36
d. When you do not use the robot for some time, please fully charge the battery first, then
DO7293S
switch off the robot and keep it in a cool but dry place.
Fig a
show
Fig a
show
Fig. 1
Fig. 2
when the battery level is low.
when the battery level is low.
10
Fig b
Fig b