To Avoid Problems - Pioneer DRM-7000 Mode D'emploi

TO AVOID PROBLEMS

The following is a list of operation items that may potentially lead to problems in component functioning.
÷ Do not place foreign objects inside the changer, since malfunction
1. Installation
÷ Do not use the changer in locations subject to high concentrations
÷ Do not subject the recorder to impact or vibration during use.
÷ When connecting exterior SCSI cable, be sure that power is first
2. Connections
÷ When installing a drive, be sure to connect the changer interface
÷ The final device on a SCSI bus must have its terminator switched
÷ When installing a drive, if the wiring monitor indicator does not flash,
÷ Never disconnect power while the changer is transporting a disc, or
3. Power ON/OFF
÷ When turning the power off and then on again, wait at least ten
÷ During data recording, do not send commands from the disc writer
4. Control
÷ When transporting the unit, pack the unit in its original packaging
5. Transporting Unit
÷ Do not transport the unit with drive units, 50-disc magazines or other
÷ Do not transport disc magazines with discs loaded.
÷ E8❋, E9❋, EF8, or EF3 errors cannot be corrected merely by reset-
6. Error Correction
12
<DRC1285>
En
Issue
may result.
of dust, heat, or humidity.
* Do not install in locations directly exposed to outdoor dust or air.
* Do not install near air conditioner vents or air cleaners.
* Do not install in hallways or other areas near frequent pedestrian
traffic.
turned off to host computer and changer.
* When connecting internal SCSI cable, power may be left while
connecting.
cable to the connector corresponding to the bay in which the drive
is installed. If the cable is mistakenly connected to a neighboring
connector, the discs may be damaged and the E99 error may occur.
ON, or an external terminator device used. The changer may oper-
ate erratically if proper termination is not provided. If no termination
is used and malfunctions occur, turn termination on before restoring
power to the changer.
* If the final device on a SCSI bus (with terminator turned ON) is
removed from the bus, or if its SCSI cable is disconnected, it means
that bus termination is not provided from that time, and the same
kind of malfunctions may occur as described above.
recheck and install the power cable connection, followed by the
changer interface connection.
when the writer is recording data to a disc.
seconds after turning the power off before turning it on again.
to remove disc (Move Medium, Rezero Unit), since EC❋ error or
write malfunction may occur (back buffer underrun).
materials, and ship in an upright position. Do not transport the unit
on its side.
optional accessories loaded (except for 20-disc hyper-magazine).
When transporting the accessories, repack them in their original
packaging materials.
ting the changer's power on/off. The system administrator mode
must be used to open and then close the door again. For these and
other errors, see the Operating Instructions, p. 46.
Potential Malfunction/Error
÷ [E83], [E99], [E88]
÷ Recording/playback mal-
function
÷ Recording/playback mal-
function
÷ Changer malfunction
÷ [E83], [E99]
÷ Display window (LCD)
doesn't appear correctly.
÷ Operation keys malfunc-
tion.
÷ Changer not recognized
on the SCSI.
÷ Changer does not detect
drive.
÷ Changer malfunction.
÷ Data recording malfunc-
tion
÷ Recording malfunction
÷ [EC❋], (where ❋ = 0 – F)
÷ [E8❋], [E9❋], [EF8], [EF3]
(where ❋ = 0 – F)