Briteq LD-POWER 60 Mode D'emploi page 7

ENGLISH
HOW TO SETUP:
MAIN MENU:
 To select any of the menu options, press the MENU button up to when the required one is shown on the
display.
 Select the function with the ENTER button. The display will blink.
 Use DOWN and UP button to choose the desired menu option.
 Once the required menu option is selected, press the ENTER button to select.
 Press the MENU button for 2seconds to save the settings and go back to normal working mode.
The menu structure is shown below.
DMX512 Address Setting
Used to set the starting address in a DMX
setup.
 Press the MENU button until is shown
on the display.
 Press the ENTER button, the display starts
blinking.
 Use DOWN and UP buttons to change the
DMX512 address.
 Once the correct address shows on the
display, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds
to save the setting and return to running
mode, press shortly to return without saving.
Channel Mode
Used to set the desired channel mode.
 Press the MENU button until
is shown
on the display.
 Press the ENTER button, the display starts
blinking.
 Use DOWN and UP button to select one of the
7 working modes:
 Modes 1+2: used with RGBW projectors.
 Modes 3+4: used with RGB projectors.
 Modes 5+6: used with combined WW/CW
projectors to control light temperature.
 Mode 7: used for WW or CW projectors.
 Check the different DMX-charts.
 Once the correct address shows on the
display, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds
to save the setting and return to running
mode, press shortly to return without saving.
Show Mode
Used to select one of the 19 shows while used in standalone or master/slave mode.
 Press the MENU button until
is shown on the display.
 Press the ENTER button to select.
 Use DOWN and UP buttons to select one of the 19 preprogrammed shows.
 Press ENTER to confirm, now you also have to set:
 Fade time: the display shows "Fxxx", where xxx ranges from 000 (corresponding to 0,256sec) to 255
(corresponding to 18 hours for 1 fade over)
 Use DOWN and UP buttons to select desired fade time.
BRITEQ (LD-SERIES)
®
OPERATION MANUAL
9/65 LD-POWER60 / LD-POWER120
ENGLISH
 Press ENTER to confirm
 Wait time: the display shows "Uxxx", where xxx ranges from 000 (corresponding to 0,256sec) to 255
(corresponding to 18 hours waiting before the next fade over occurs)
 Use DOWN and UP buttons to select desired wait time.
 Press ENTER to confirm (you will return to show selection)
 Press the MENU button for about 2 seconds to save the setting and return to running mode, press shortly
to return without saving.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to master mode.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the current selection starts blinking in the display.
 Use DOWN and UP button to select Y E S (blackout) or n o (no blackout) mode.
 Once the mode is selected, press the ENTER button to save it.
 Press the MENU button for about 2 seconds to save the setting and return to running mode, press shortly
to return without saving.
Program Mode
From the 19 shows, shows 17 to 19 can be edited by the user with a maximum of 42 steps.
 Press the MENU button until
is shown on the display.
 Press the ENTER button to select.
 Use DOWN and UP buttons to select one of the 3 user editable shows: 17, 18 or 19
 Press ENTER to confirm, now you can edit the selected show:
 Show length: a show can contain up to 42 steps, select how many steps of the show you want to use.
 The display shows
, press ENTER to see how many steps are currently selected.
 Use DOWN and UP buttons to adjust to the desired number of steps.
 Press ENTER to confirm.
 Press the UP button to start programming the steps.
 Programming each step: now we can start setting the different colors for each step.
 The display shows
, press ENTER to see how many steps are selected.
 Use DOWN and UP buttons to select desired number of steps.
 Press ENTER to confirm.
 The display shows the first step (St 1), press ENTER to edit this step:
 [SET COLOR] The display shows
POWER120), press ENTER to edit this color:
 Use DOWN and UP buttons to select one of the 255 colors.
 Press ENTER to confirm.
 [ADD WHITE] Press the UP button: the display shows
(zone 1 / 2 on LD-POWER120).
 If you have RGBW projectors and want to add white, press ENTER and set the amount of white.
If you only have RGB projectors: press the UP button again
 [SET DIMMER] The display shows
LD-POWER120), press ENTER to edit the output level for the current step:
 Use DOWN and UP buttons to set the level from 000 (off) to 255 (100%).
 Press ENTER to confirm.
 If all parameters for Step1 are OK, press the MENU button shortly followed by the UP button 
the display now shows the second step (St 2): you can adjust all settings for step2
 When all parameters are set, press the MENU button for 2seconds to return to working mode.
Manual Mode
Used to test all colors of the projectors connected to both output zones.
 Press the MENU button until
is shown on the display.
 Press the ENTER button to select: the display shows
BRITEQ (LD-SERIES) 10/65
®
OPERATION MANUAL
(LD-POWER60) or / (zone 1 / 2 on LD-
(LD-POWER60) or
(LD-POWER60) or / (zone 1 / 2 on
(LD-POWER60) or (LD-POWER120)
LD-POWER60 / LD-POWER120
/