Whirlpool P8WB2L Instructions D'installation page 6

Replace the Doors and Hinges
1. Replace both bottom hinges, if removed. Make sure that the
leveler brackets are assembled behind the hinges. Tighten
screws.
IMPORTANT: When the screws are tightened properly, there
should not be any gaps between the refrigerator, leveler
bracket and hinge.
WARNING
Excessive Weight Hazard
Use two or more people to lift the freezer door.
Failure to do so can result in back or other injury.
2. Before replacing the freezer door on the bottom left hinge,
feed the wiring and water tubing through the hinge.
On models with the ice storage bin on the door:
Feed the small wiring bundle through the hinge.
■
Assistance may be needed.
IMPORTANT: Do not feed the large wiring bundle through the
hinge. This bundle is intended to run directly from the door to
the connections beneath the freezer. Forcing the large bundle
through the hinge may damage the door and/or the wiring,
and will keep the door from closing properly.
Feed both water tubes through the bottom left hinge, then
■
replace the freezer door on the hinge. Assistance may be
needed.
On models with the ice storage bin inside the freezer:
Feed the wiring bundle through the hinge. Assistance may
■
be needed.
Feed the water tube through the bottom left hinge, then
■
replace the freezer door on the hinge. Assistance may be
needed.
NOTE: Provide additional support for the doors while the top
hinges are being replaced. Do not depend on the door magnets
to hold the doors in place while you are working.
3. Align and replace the top left hinge as shown. See Graphic 4.
Tighten screws.
4. Reconnect water tubing and wiring.
IMPORTANT: Do not intertwine the water tubing and wiring
bundles when reconnecting them.
On models with the ice storage bin on the door:
Water Connection Style 1: Push the larger 5/16" (7.94
■
mm) water tube into the blue fitting until it stops, then
push the smaller 1/4" (6.35 mm) water tube into the green
fitting until it stops. See Graphic 2A.
Water Connection Style 2: Push the black water tube
with the blue tip into the blue fitting until it stops. Close
the clasp around the tubing, making sure it snaps into
place. Repeat this process to connect the red-tipped
black water tube and the red fitting. See Graphic 2B.
Reinstall the P-clamp around the small wiring bundle (with
■
one yellow plug), then replace the P-clamp on the top
screw hole of the routing plate. See Graphic 3.
Gently route the large wiring bundle (with two white plugs)
■
through the hole in the routing plate, so that the wiring
runs behind the right side of the routing plate. See Graphic
3.
NOTE: The large wiring bundle should always remain
below the small wiring bundle.
6
Reconnect the wiring plugs to the electrical housing, then
■
push the housing back under the refrigerator. Align the left
hole in the front lip of the housing with the right hole in the
refrigerator's base crossbar. See Graphic 3.
Reinstall the wiring clip over the grommets. First install the
■
smaller grommet into the top of the clip, then install the
larger grommet into the bottom of the clip (closest to the
screw hole). See Graphic 3.
Align the clip's screw hole with the left hole in the
■
electrical housing and the right hole in the crossbar, and
screw in the clip using a single screw. Tighten screw. See
Graphic 3.
IMPORTANT: Once connected, the wiring bundles should
not be taut. Some flexibility is needed to allow the freezer
door to open properly.
On models with the ice storage bin inside the freezer:
Water Connection Style 1: Push the water tube into the
■
fitting until it stops. See Graphic 2A.
Water Connection Style 2: Push the water tube into the
fitting until it stops. Close the clasp around the tubing,
making sure it snaps into place. See Graphic 2B.
Reconnect the wiring plug to the electrical housing, then
■
push the housing back under the refrigerator. Align the left
hole in the front lip of the housing with the right hole in the
refrigerator's base crossbar. See Graphic 3.
Reinstall the wiring clip over the grommet. See Graphic 3.
■
Align the clip's screw hole with the left hole in the
■
electrical housing and the right hole in the crossbar, and
screw in the clip using a single screw. Tighten screw. See
Graphic 3.
IMPORTANT: Once connected, the wiring should not be
taut. Some flexibility is needed to allow the freezer door to
open properly.
5. Replace the refrigerator door by lifting the door onto the
bottom right hinge.
6. Align and replace the top right hinge as shown. See Graphic
6. Tighten screws.
7. Replace the ice storage bin (on some models) and any
adjustable door or utility bins.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
8. Plug refrigerator into a grounded 3 prong outlet.