Additional Safety And Working Instructions - Bosch GBH 14,4 V-LI Compact Professional Notice Originale

OBJ_BUCH-1331-005.book Page 10 Monday, September 19, 2016 8:49 AM
10 | English
Additional Safety and
Working Instructions
 Use appropriate detectors to determine if utility lines
are hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age.
 If the application tool should become blocked, switch
the machine off. Loosen the application tool.
 Before switching on the power tool, make sure that the
application tool moves freely. When switching on with a
blocked drilling tool, high torque reaction can occur.
 For drilling without impact in wood, metal, ceramic and
plastic as well as for screwdriving, tools without SDS-plus
are used (e.g., drill bits with cylindrical shank). For these
tools, a keyless chuck or a key type drill chuck are re-
quired.
 Replace a damaged dust protection cap immediately.
The dust protection cap largely prevents the penetration of
drilling dust into the tool holder during operation. When in-
serting the tool, pay attention that the dust protection cap
is not damaged.
 The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery
in the battery charger before using your power tool for
the first time.
 Read the operating instructions of the battery charger.
 Check the tight seating of the battery. Two locking lev-
els are possible.
 Apply the power tool to the screw/nut only when it is
switched off. Rotating tool inserts can slip off.
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
 Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
 In case of damage and improper use of the battery, va-
pours may be emitted. Ventilate the area and seek
medical help in case of complaints. The vapours can irri-
tate the respiratory system.
 Use the battery only in conjunction with your Bosch
power tool. This measure alone protects the battery
against dangerous overload.
 The battery pack can be damaged by pointed objects
such as nails or screwdrivers or by force applied exter-
1 609 92A 2MF | (19.9.16)
nally. An internal short circuit can occur and the battery
pack can burn, smoke, explode or overheat.
 When transporting and storing, set the rotational di-
rection switch to the centre position. Danger of injury
when accidentally actuating the On/Off switch.
 When switching on with a blocked drilling tool, high
torque reaction can occur.
 Avoid unintentional switching on. Ensure the On/Off
switch is in the off position before inserting battery
pack. Carrying the power tool with your finger on the
On/Off switch or inserting the battery pack into power
tools that have the switch on invites accidents.
 Inserting SDS-plus Drilling Tools: Check the latching by
pulling the tool.
 Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health and cause allergic reactions, lead to res-
piratory infections and/or cancer. Materials containing
asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dust can
easily ignite.
 To save energy, only switch the power tool on when using
it.
Symbols
The following symbols are important for reading and under-
standing the operating instructions. Please take note of the
symbols and their meaning. The correct interpretation of the
symbols will help you to use the machine in a better and safer
manner.
Symbol Meaning
GBH 14,4 V-LI Compact/
GBH 18 V-LI Compact:
Cordless Rotary Hammer
Grey-marked area: Handle (insulated
gripping surface)
Article number
Read all safety warnings and all instruc-
tions
Before any work on the machine itself,
remove the battery from the power
tool.
Bosch Power Tools