Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
5) Repeat steps 2 to 4 for all further units to be
adjusted which are required for the scene.
6) Press button PROGRAM REC.
7) If the presently activated memory bank is not
desired, select the memory bank with the but-
tons
and
(4). Indication
(bank 4).
8) Press the button in the field COLOUR PRE-
SETS 1 to 8 under which the scene is to be
memorized. All LEDs of the control panel flash
three times.
9) With button DEL/CLEAR (5) all LEDs of the
spotlights may be turned off. It is not necessary
to select them and to move the controls 1 to 4.
This may e. g. be useful as a basic setting for
the next scene.
10) To memorize further scenes, repeat steps 2 to 8.
11) After all desired scenes have been memorized,
switch off the programming mode. For this pur-
pose keep button PROGRAM REC pressed for
approx. 3 seconds until its LED stops flashing.
5.2.2 Calling scenes
1) With the buttons
bank in which the desired scene has been memo-
rized. Indication
2) Call the desired scene and if necessary, switch
it off again with the buttons COLOUR PRESETS
(1). Indication
scene 1) to
(bank 4, scene 8).
If one of buttons COLOUR PRESETS is
pressed under which no scene has been mem-
orized yet, the display shows
the scene selected before remains switched on.
3) A scene called can be changed with the controls
1 to 4 (8 to 11) but the change will not be mem-
orized.
5.2.3 Deleting scenes
1) First switch on the programming mode. For this
purpose keep button PROGRAM REC (2)
pressed for approx. 3 seconds until its LED
starts flashing.
2) If necessary, use the buttons
select the memory bank in which the scene to
be deleted has been memorized.
3) Keep button DEL / CLEAR (5) pressed and then
press the corresponding button in the field
COLOUR PRESETS (1) at the same time. All
LEDs of the control panel flash three times.
4) To delete further scenes, repeat steps 2 and 3.
(bank 1) to
and
(4) select the memory
(bank 1) to
(bank 4).
(Colour Preset bank 1,
. However,
and
5) After deleting, switch off the programming
mode. For this purpose keep button PROGRAM
REC pressed for approx. 3 seconds until its LED
stops flashing.
5.3 Programming and
replaying a sequence of scenes
To programme sequences of scenes (chases), 8
memory locations are available. On each memory
location a sequence of up to 32 scenes may be pro-
grammed. The scenes of a sequence can be
advanced manually, by music control or automati-
cally at adjustable speed.
5.3.1 Programming a sequence of scenes
1) Switch on the programming mode. For this pur-
pose keep button PROGRAM REC (2) pressed
for approx. 3 seconds until its LED starts flash-
ing. If sequences of scenes have already been
programmed, the corresponding LEDs of the
buttons CHASES (6) flash.
2) Press the button in the field CHASES (6) under
which the sequence of scenes is to be memo-
rized. The display shows
the sequence of scenes has yet been memorized.
3) Adjust the first illumination scene with the but-
tons FIXTURE SELECTOR 1 – 8 (7) and the
controls 1 to 4 (9 to 11).
However, it is also possible to call a scene
already memorized with a button in the field
COLOUR PRESETS (1) and to use it for the
sequence of scenes (
4) To memorize the scene, press button PRO-
GRAM REC. To confirm the memory procedure,
all LEDs of the control panel flash three times
and
sequence.
5) With button DEL / CLEAR (5) all LEDs of the
spotlights can be turned off. It is not necessary
to select them and to move the controls 1 to 4.
This may e. g. be useful as a basic setting for
the next scene.
6) Adjust and memorize the next scene (steps 3
(4) to
to 5). Thus, up to 32 scenes may be memorized
for the sequence. If you try to memorize one
more scene, the display shows
7) After the desired sequence of scenes has been
memorized, switch off the memory mode. For
this purpose keep button PROGRAM REC
pressed for approx. 3 seconds until its LED
stops flashing.
, i. e. no step for
chapter 5.2.2).
is displayed for the 1
st
GB
scene of the
.
15
Publicité
Chapitres
Table des Matières
