Checking Oil Level; Liste Des Pièces - Powerbuilt TRIPLE LIFT Manuel D'utilisation Et D'entretien

CHECKING OIL LEVEL

Do not use brake or transmission fluids, or regular motor oil as they can damage the seals. Always purchase and
use products labeled Hydraulic Jack Oil.
1. Turn handle counterclockwise to allow ram to fully retract. It may be necessary to apply force to the saddle
for lowering.
2. With jack in upright position remove oil fill plug. Oil should be even with bottom of hole. If not, top up.
Do not overfill. Always fill with new, clean hydraulic jack oil.
3. Replace fill plug.
4. Check jack operation.
At this time, consult Troubleshooting section for System Air Purge.
1. Owners and/or operators should be aware that repair of this equipment may require special knowledge and
facilities.
2. It is recommended that an annual inspection of the jack be made and that any defective parts, decals, or safe-
ty labels or signs be replace with manufacturer's specified parts.
3. Any jack that appears to be damaged in anyway, is found to be worn, or operates abnormally shall be
removed from service until repaired.
4. Because of the potential hazards associated with this type of equipment, no alterations shall be made to this
product.
5. Do not mix different types of oil together. When filling the jack with oil, do not permit dirt or any other sub-
stance to enter the hydraulic system.
Symptoms Solutions
Will not lift load See below
Will not hold load See #3
Will not lift to full height See #1 and #2
Pump feels "spongy" under load See #1 and #2
Handle raises under load See #3
Handle lowers under load See #3
1. The power unit may be low on fluid. With the jack on a level surface and in the down position, remove
the oil plug and add clean hydraulic jack fluid to the level of the oil plug hole.
2. The power unit may have trapped air. Open the release valve a minimum of two full turns. Pump the
handle a minimum of 20 strokes to purge the air from the system.
3. Valves may not be closing properly. To seat the valves: A) Close the release valve. B) With the ram fully
lowered, manually lift the boom as high as possible. C) Open the release valve and allow the boom to
descend to the lowered position.
Any hydraulic jack found to be damaged in any way, is found to be worn or operates abnormally "SHALL BE
REMOVED FROM SERVICE UNTIL REPAIRED". Owners and/or operators should be aware that repair of the
equipment requires specialized knowledge and facilities. Only factory authorized parts, labels and decals shall
be used on this equipment. Call the customer service department. Annual inspections must be performed,
please call our customer service number 1-800-423-3598 for recommended authorized repair facility.
Because of the potential hazards associated with the misuse of equipment of this type, no alterations shall be
made to the product without written authorization of the manufacturer or supplier.
MAINTENANCE
TROUBLESHOOTING
FACTORY SERVICE
ALTERATIONS
6
LISTE DES PIÈCES
Nº Description Qté.
1 Unité hydraulique 1
2 Boulon de fixation de la poignée1
3 Ensemble de roulettes 2
4 Fourche de poignée 1
5 Poignée 2
6 Bras de levage 1
7 Roue 2
8 Bras de liaison 2
9 Barre de fixation 1
10 Grand patin 2
11 Petit patin 1
12 Protection de la sellette 1
13 Sellette 1
14 Plate-forme de la sellette 1
11
10
5
6
4
2
1
17
SPÉCIFICATIONS
Capacité max. 4000 lbs. (1814 kg)
Longueur de la base (fourche incluse) 24-1/2 po (62,4 cm)
Largeur de la base 13-3/4 po (34,9 cm)
Hauteur de la base (sans la poignée) 7-1/4 po (18,4 cm)
Hauteur de levage minimale (avec sellette) 6 po (15,24 cm)
Hauteur de levage minimale (sans sellette) 5-1/2 po (13,97 cm)
Hauteur de levage maximale (avec sellette) 17-1/2 po (44,45 cm)
Hauteur de levage maximale (sans sellette) 17 po (43,18 cm)
Poids total 86,9 lbs. (39,4 kg)
12
13
14
8
9
3
7
7