Milwaukee 0100-20 Manuel De L'utilisateur page 5

Keyed Chuck
These tools are equipped with a chuck tightened
using a key. Always unplug the tool before installing
or removing bits.
1. To open the chuck jaws,
place the chuck key in
one (1) of the three (3)
holes located on the
chuck. Turn the key
counterclockwise.
Be sure the bit shank
and chuck jaws are
clean. Dirt particles
may prevent the bit
from lining up properly.
2. When using drill bits, insert the bit into the chuck.
Center the bit in the chuck jaws and lift it about
1/16" off of the bottom. Tighten the chuck jaws by
hand to align the bit.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the bit shank.
Tighten the chuck jaws by hand to align the bit.
3. To close the chuck jaws, place the chuck key in
each of the three holes in the chuck. Turn the
chuck key clockwise. Tighten securely.
4. To remove the bit, insert the chuck key into one
of the holes in the chuck. Turn the chuck key
counterclockwise.Be sure the bit shank and chuck
jaws are clean. Dirt particles may prevent the bit
from lining up properly.
To reduce the risk of injury, do not
WARNING
grasp the bit while the chuck is
rotating or while the bit is falling from the chuck.
Double Sleeve Keyless Chuck
These tools are equipped with a hand tightening key-
less chuck. Always unplug the tool before installing
or removing bits.
1. To open the chuck jaws,
hold the collar and turn
the sleeve counterclock-
wise.
Be sure the bit shank
and chuck jaws are
clean. Dirt particles may
prevent the bit from lin-
ing up properly.
2. When using drill bits,
insert the bit into the
chuck. Center the bit in
the chuck jaws and lift it
about 1/16" off of the
bottom. Tighten the
chuck jaws by hand to
align the bit.
When using screwdriver
bits, insert the bit far enough for the chuck jaws to
grip the bit shank. Tighten the chuck jaws by hand
to align the bit.
3. To close the chuck jaws,
hold the collar and turn
the sleeve clockwise.
Tighten securely.
4. To remove the bit, hold
the chuck collar and turn
the sleeve counterclock-
wise to release the bit from the chuck jaws.
Tighten
Loosen
Tighten
Loosen
To close
Sleeve
Collar
Single Sleeve Keyless Chuck
These tools are equipped with a spindle-lock mecha-
nism and a single-sleeve keyless chuck. Always
unplug the tool before inserting or removing bits.
1. To open the chuck jaws,
turn the chuck sleeve
counterclockwise.
Be sure the bit shank
and chuck jaws are
clean. Dirt particles may
prevent the bit from lin-
ing up properly.
2. When using drill bits,
insert the bit into the
chuck. Center the bit in
the chuck jaws and lift it
about 1/16" off of the
bottom. Tighten the
chuck jaws by hand to
align the bit.
When using screwdriver
bits, insert the bit far
enough for the chuck
jaws to grip the bit shank. Tighten the chuck jaws
by hand to align the bit.
3. To close the chuck jaws,
turn the chuck sleeve
c l o c k w i s e . Ti g h t e n
securely. Several de-
tents will be felt as the
chuck sleeve is turned.
NOTE: If the spindle rotates when opening or clos-
ing the chuck jaws, grasp the chuck and slightly
rotate back and forth to engage the spindle-lock
mechanism.
The spindle will remain locked until the tool is
turned on. The spindle-lock mechanism will auto-
matically disengage when the tool is turned on.
4. To remove the bit, turn the chuck sleeve counter-
clockwise to release the bit from the chuck jaws.
To reduce the risk of injury, always
WARNING
wear eye protection.
Chuck Removal
This tool is equipped with a threaded spindle to hold
the chuck. Before removing the chuck, unplug the tool
and open the chuck jaws. A left-handed thread screw
is located inside the chuck to prevent the chuck from
loosening when the tool is operated in reverse direc-
tion. Remove the screw by turning it clockwise. To
remove the chuck, hold
the tool so that only the
side of the chuck rests
firmly and squarely on
a solid workbench. In-
sert the chuck key or a
chuck remover bar in
one of the keyholes.
Turn the chuck so the
key is at about a 30°
angle to the bench top
and strike the key
sharply with a hammer so the chuck turns in a coun-
terclockwise direction (looking from the front of the
tool). This should loosen the chuck from the spindle
which has a right hand thread making it easy to remove
the chuck by hand.
NOTE: When replacing the chuck, always replace
the left hand thread screw in the chuck.
5
Tighten
Loosen
To close
Sleeve