Assembly Material; Proper Use - EINHELL RT-VE 550 Mode D'emploi D'origine

Masquer les pouces Voir aussi pour RT-VE 550:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 16
Anleitung_RT_VE_550_SPK1:_
Important!
When using the equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating instructions with
due care. Keep this manual in a safe place, so that
the information is available at all times. If you give
the equipment to any other person, hand over these
operating instructions as well. We cannot accept any
liability for damage or accidents which arise due to a
failure to follow these instructions and the safety
instructions.
1. Layout (Fig. 1-2)
1. Dust bag hook
2. Dust bag
3. Quick clamp device for dust bag
4. Transportation handle
5. Quick clamp device for debris bag
6. Debris bag
7. Base plate
8. Chassis
9. Strengthening plate
10. Wheels
11. Extractor hose
12. Side panels
13. Plastic housing
14. Hole for dust bag hook
15. ON/OFF switch
16. Motor
17. Connection adapter

1.2 Assembly material

A. 2 x Hose fastening
B. 4 x Screw for strengthening plate
C. 8 x Nut
D. 4 x Screw for chassis
2. Supplied package (Fig. 2)
Dust bag hook (1)
Dust bag (2)
2 x Quick-release device (3/5)
Debris bag (6)
Chassis (8)
Strengthening plate (9)
Suction hose (11)
2 x Side plate (12)
Plastic housing (13)
Connection adapter (17)
Assembly material (see point 1.2)
27.11.2009
8:04 Uhr
Seite 13

3. Proper use

The vacuum extraction system is designed for
extracting chippings and dust arising from the
processing of wood or wood-type materials. Never
use this equipment in an environment where there is
a risk of fire and explosion.
The machine must only be used for its intended
purpose!
Any other use is deemed to be a case of misuse.
The user/operator and not the manufacturer will be
held liable for damage and/or injuries of any kind that
result from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
To use the machine properly you must also observe
the safety regulations, the assembly instructions and
the operating instructions to be found in this manual.
All persons who use and service the machine have
to be acquainted with this manual and must be
informed about the machineʼs potential hazards.
It is also imperative to observe the accident
prevention regulations in force in your area.
The same applies for the general rules of
occupational health and safety.
The manufacturer shall not be liable for any changes
made to the machine nor for any damage resulting
from such changes.
Even when the machine is used as prescribed it is
still impossible to eliminate certain residual risk
factors.
The following hazards may arise in connection with
the machineʼs design and construction:
Hazard due to machine defects:
If one or more parts of the machine are
defective, the use of the machine is prohibited.
Defective parts must be replaced immediately.
Only replacement parts which have been
approved by the manufacturer may be used. It is
prohibited to make any changes to the machine.
Hazard due to electric shock:
Only operate the machine at a power source
which is protected by a residual-current circuit
breaker with a residual current of 30 mA!
Socket-outlets must be properly installed,
earthed and tested!
Hazard due to unintentional start-up of the
machine: The power plug must be removed from
the socket-outlet before emptying the sawdust
bag and also when the machine is not in use!
GB
13

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

43.041.40

Table des Matières