Operation Safety Zone; Angle Adjustment Of Accessory; Changing Of Handlebar Height; Storage - Texas COMBI 800TG Manuel D'utilisation

Note: The clutch lever is not broken but simply pushed
back into place.
The machine is equipped with a "dead man's handle",
once released the brush and drive will stop
immediately.
Wheel shaft: Fixed vs. free
•
Activate free wheel shafts, see fig. 7-A
At hard ground (e.g. paved road), it can be a
good idea to activate free wheel shafts.
•
Activate fixed wheel shafts, see fig. 7-B
At soft/lose ground (e.g. dirt road) it can be a
good idea to activate fixed wheel shafts
Generally, the machine will be easier to manoeuvre
with free wheel shafts.

Operation safety zone

Do not leave the operation safety zone marked in fig 5,
while working with the machine. If it is necessary
toleave the operation zone, for example to readjust the
rotary brush or to attach an accessory, first stop the
engine.

Angle adjustment of accessory

The accessory can be pivoted 20 degrees to either
side. This is done by pushing the swing handle down,
turning the brush and releases the handle so the
detent clicks into place.

Changing of handlebar height

1. Remove the small bolt from the gear rod
middle part (fig. 6-B).
2. Loosen the 4 bolts on the middle of handlebar
(fig. 6-A) and take the out.
3. Move the upper handlebar and the gear rod
part up/down with same number of holes
(fig. 2-F+G)
4. Mount all the bolts again on the handlebar and
gear rod and tighten them again.
5. Check that the gear rod (fig. 6-C) easily can
move into all position. If not, the bolt on the
gear rod middle part is probably not placed in
the correct hole.

Storage

Correct storage of your sweeper!
Store the sweeper, so that the brushes do not touch
the ground. This will extend the durability and lifetime
of the brushes.
•
Lower the support wheels about 50 mm so that
the brushes are floating above the ground
before the sweeper is disconnected from the
basis unit.
•
Disconnect the sweeper from the basis unit.
•
Tilt the sweeper back, so it rests on the
connection-part, and let it stand in that position
during the storage period.
Never let the brushes rest on the ground for longer
time. It will cause them to bend and be useless. Fig. 10

Troubleshooting

Problem Solution
The engine won't start:
1. Check sparkplug.
2. Check that the spark plug cap is fitted
correctly.
3. Check if the motor is equipped with an
ignition switch.
(It must be activated)
4. Check if the motor is equipped with a
fuel valve.
(It must be activated)
The engine runs unevenly:
1. Check that the choke has been released.
2. Check fuel for impurities
(or check/clean the carburetor)
If the accessory-unit makes noise or run badly:
1. Check that the accessory-unit is clicked
in place properly (fig. 5-A).
If the accessory-unit will not run:
1. Check that the cable is adjusted
correctly.
If the machine will not run:
1. Check that the cable is adjusted
correctly.
2. Check the belt.
If the machine does not sweep effectively:
1. Check the distance between the brush
and working surface.

Technical specifications

Model
Length (mm)
Width (mm)
Height (mm)
Weight, dry (kg)
Wheel size
Engine model
Engine brand
13
Combi Combi
800 TG 800 TGE
800 800
700 700
1000 1000
55.5 56
4.80-8 4.80-8
TG720S TG720ES
Texas Texas
Powerline Powerline
Combi
800 B
800
700
1000
55.5
4.80-8
950
B&S