Delivery Check; Accessories / Spare Parts - Sundstrom SR 200 Mode D'emploi

2. Parts

2.1 Delivery check

Check that the equipment is complete in ac cordance
with the packing list, and undamaged.
Packing list
• Full face mask
• Filter adapter
• Pre-filter
• Pre-filter holder
• Cleaning tissue
• ID-tag
• User instructions

2.2 Accessories / Spare parts

Fig.1.
Item Part
No.
Full face mask SR 200 w PC visor
Full face mask w glass visor
1. PC visor SR 366
1. Laminated glass visor SR 365
2. Mask body
3. Upper frame half with screws
4. Head harness, fabric
4. Rubber head harness SR 340
5. Membrane kit
a) Exhalation membranes, two
b) Valve covers, two
c) Inhalation membranes, three
d) Dowels, two
6. Pre-filter holder
7. Pre-filter SR 221
8. Particle filter P3 R, SR 510
9. Gas filter A1, SR 217
9. Gas filter A2, SR 218
9. Gas filter AX, SR 298
9. Gas filter ABE1, SR 315
9. Gas filter ABE2, SR 294
9. Gas filter K1, SR 316
9. Gas filter K2, SR 295
9. Gas filter ABEK1, SR 297
Combined filter ABEK1-Hg-P3 R,
SR 299-2
10. Filter adapter SR 280-3
11. Seal for filter connection
12. Particle filter adapter SR 611
Peel-offs SR 343, for plastic visor*
Peel-offs SR 353, for glass visor*
Spectacle frame for corrective
lenses SR 341, fig. 19
Welding Cassette SR 84, fig. 20*
Voice Amplifier SR 324, fig. 21*
Test adapter SR 370, fig. 22*
Storage box SR 344, fig. 23*
Storage bag SR 339-1, fig. 24*
Storage bag SR 339-2, fig. 24*
Carrier strap
ID-tag SR 368
Cleaning tissues SR 5226, box of 50* H09-0401
* Must not be used in potentially explosive atmosphere.
3. Use
3.1 Installation
3.1.1 Filters
You can identify various filters by the colour and protection
designation of the filter label.
Note. A particle filter provides protection only against
particles. A gas filter provides protection only against
gases/vapours. A combined filter protects against both
gases/vapours and particles.
3.1.1.1 Particle filters
Ordering No.
The Sundström particle filter traps and holds particles
in the filtering media. As the amount of the captured
H01-1212
contaminant in the media increases, breathing resist-
H01-1312
ance also increases. Replace the filter after 2 – 4
R01-1201
weeks or sooner if breathing resistance becomes no-
T01-1203
ticeable. Filters are consumables with a limited service
-
life. A filter exposed to strong press or impact or with
R01-1202
visible damage must immediately be scrapped.
R01-1203
T01-1215
3.1.1.2 Gas filters
R01-1204
-
Each gas filter is designed to provide respiratory protec-
-
tion against specific contaminants. A gas filter absorbs
-
and/or adsorbs specific vapours and gases from a
-
contaminated atmosphere. This process continues
R01-0605
until the absorbent becomes saturated and allows the
H02-0312
contaminant to break through.
H02-1312
We recommend that the gas filter/combined filter should be
H02-2512
changed in accordance with the results of measurements
H02-2012
carried out at the worksite. If this is impossible, change
H02-2412
the filter every week or earlier if you can smell or taste
H02-3212
the pollutants or if you experience any other discomfort.
H02-3312
A filter exposed to strong press or impact or with visible
H02-4212
damage must immediately be scrapped.
H02-4312
3.1.1.3 Combined filters
H02-5312
In environments in which both gases and particles occur,
H02-6512
such as in spray painting, gas and particle filters must
H09-0212
be combined.
R01-1205
T01-1223
• Place the particle filter on top of the cartridge. Grasp
T01-1204
both protective elements.
T01-1205
• Squeeze hard until you hear the particle filter snap
onto the gas filter. Fig. 1a.
T01-1201
• Place a pre-filter into the pre-filter holder.
T01-1212
• Snap the pre-filter holder on the filter or cartridge.
T01-1217
T01-1206
Note. The particle filter will always be snapped on the gas
T01-1214
filter, but the gas filter will not snap onto the particle filter.
H09-0113
The gas filter will always be inserted into the respirator.
H09-0114
R01-1206
R09-0101
29