Delivery Check; Accessories / Spare Parts - Sundstrom SR 592 Mode D'emploi

2. Parts

2.1 Delivery check

Check that the equipment is complete in accordance with the
packing list, and undamaged.
Packing list
Fig. 3
1. Welding shield
2. Breathing hose
3. User instructions
4. Cleaning tissue

2.2 Accessories / Spare parts

Fig. 4
Item
1. Welding shield SR 592
2. Breathing hose
3. O-ring to breathing hose, against fan unit
O-ring to breathing hose, against shield
4. Face seal SR 592
5. Head harness SR 592
6. Sweatband SR 592, 5-pack
7. Welding filter, shade No. 8, SR 59008
Welding filter, shade No. 9, SR 59009
Welding filter, shade No. 10, SR 59010
Welding filter, shade No. 11, SR 59011
Welding filter, shade No. 12, SR 59012
Welding filter, shade No. 13, SR 59013
Welding filter, EN 3/10, SR 59005
Welding filter, EN 3/11, SR 59006
Welding filter, EN 4/5-13
Welding filter, 4/9-13, SR 59007
8. Outer protective lens SR 592
10. Inner protective lens for auto lens
Inner protective lens for R06-4508
11. Correction lens, dptr 1,0, SR 59014
Correction lens, dptr 1,5, SR 59015
Correction lens, dptr 2,0, SR 59016
Correction lens, dptr 2,5, SR 59017
12. Holder welding filter SR 592
13. Screw SR 592
14. Protective hood
15. Cleaning tissues SR 5226, box of 50
24
3. Use
3.1 Installation
See also the user instructions for fan unit SR 500/SR 700
whichever is used.
Welding filter
Fit a welding filter. See section 4.4.3 To change the welding
filter.
Breathing hose
Connect the breathing hose according to fig. 5.
3.2 Putting the welding shield on and
Ordering. No.
adjustements
H06-4412
Note that the equipment must always have supplied air before
R06-4401
putting on. See the user instructions for fan unit SR 500/SR 700
R06-0202
whichever is used.
R06-4402
R06-4404
• Raise the visor and put the welding shield on. Fig. 6.
• If necessary, adjust the head harness, see fig. 7.
R06-4403
R06-4405
Height adjustment.
T06-4001
A - how high the welding shield sits on the head.
T06-4002
T06-4003
Angle adjustment between shield and head harness.
T06-4004
B - the angle against the shield.
T06-4005
Space adjustment between shield and head har-
T06-4006
ness.
T06-4007
C - the space to the shield.
T06-4008
R06-4508
Width adjustment of the head harness.
T06-4009
D - adjustment of the width of the head harness.
R06-4008
• Lower the visor unit by pulling the face seal down under
R06-4009
your chin. Fig. 8.
R06-4509
• Insert a finger between your chin and the face seal and
T06-4010
run the finger along the contact surface of the face seal
T06-4011
all the way round to check that it fits well and comfortable
T06-4012
against the face, fig. 9. Adjust the comfort of the face seal
with the drawstring, fig 10.
T06-4013
The ears should be outside the face seal.
R06-4306
• Check and adjust so that the breathing hose runs along
R06-4305
your back and that it is not twisted. Fig. 11.
T06-4014
3.3 Taking off the welding shield
H09-0401
Do not take off the equipment until clear of the hazardous area.
See also the user instructions for fan unit SR 500/SR 700
whichever is used.