Siemens euroset 2020 Mode D'emploi page 10

28.01.2000 2020-IM1-eng.fm
euroset 2020, A31008-E2020-B100-1-3S19
R R R R e e e e c c c c a a a a ll ll ll ll k k k k e e e e y y y y ( ( ( ( u u u u s s s s e e e e o o o o n n n n p p p p r r r r i i i i v v v v a a a a t t t t e e e e P P P P AB
During a trunk call, you can make an enquiry call or transfer a call. To do
this, press the recall key . The next step depends on your PABX. In the
factory setting, the recall key function is set to a flash time (interrupt time)
of 90 ms to permit new features to be used on p p p p u u u u b b b b l l l l i i i i c c c c telephone systems.
When your telephone is connected to a p p p p r r r r i i i i v v v v a a a a t t t t e e e e PABX, it may be necessary
to change the flash time (e.g. 600 ms). Please check the operating instruc-
tions for your PABX.
S S S S e e e e t t t t t t t t i i i i n n n n g g g g t t t t h h h h e e e e f f f f l l l l a a a a s s s s h h h h t t t t i i i i m m m m e e e e f f f f o o o o r r r r t t t t h h h h e e e e r r r r e e e e c c c c a a a a ll ll ll ll k k k k e e e e y y y y
Lift the handset, then start the function.
Enter the required flash time number:
...
0 0 0 0 : : : : 90 ms (factory setting);
2 2 2 2 : 270 ms;
Press the set key, then replace the handset.
Using functions for additional services on
public telephone systems
If you wish to use services that are activated with the recall key, you should
first make sure that the correct flash time is set for the key.
R R R R e e e e c c c c a a a a ll ll ll ll k k k k e e e e y y y y ( ( ( ( on on on on p p p p u u u u b b b b l l l l i i i i c c c c t t t t e e e e l l l l e e e e p p p p h h h h on on on one e e e s s s s y y y y s s s s t t t t e e e e m m m m s s s s ) ) ) )
This key is required in order to use certain additional services on public tel-
ephone systems, for example "Callback on busy".
N N N N o o o o t t t t e e e e :
Depending on the country where the telephone is used, it may be neces-
sary to set the appropriate flash time before using the recall key (see "Set-
ting the flash time for the recall key" on page 10). Your public telephone
system offers a range of additional useful services - some of them only
available on order/application (e.g. call number transmission, call forward-
ing, callback on busy, timed reminder, etc.).
U U U U s s s s i i i i n n n n g g g g c c c c a a a a ll ll ll ll n n n n u u u u m m m m b b b b e e e e r r r r t t t t r r r r a a a a n n n n s s s s m m m m i i i i ss ss ss ssi i i i on on on on
Under the f f f f o o o o l l l l l l l l o o o o w w w w i i i i n n n n g g g g c c c c on on on ond d d d i i i i t t t t i i i i on on on ons s s s call numbers for received calls will be (a)
s s s s h h h h o o o o w w w w n n n n on on on on t t t t h h h h e e e e d d d d i i i i s s s s p p p p l l l l a a a a y y y y of the Euroset 2020 and (b) all received calls will be
automatically stored in a c c c c a a a a l l l l l l l l l l l li i i i s s s s t t t t :
• Both your operator and the caller's operator provide call number trans-
mission.
• Both you and the caller have applied to the operator for this service (if
necessary).
If these requirements are met, but a caller has chosen to suppress call
number transmission before making the call, the display will show
" " instead of a (flashing) number.
_ _ _ _ _ _ _ _ _
Up to 20 digits of a call number can be shown on the display. Longer call
numbers are cut off from the start of the number (e.g. the prefix).
ABX X X X s s s s ) ) ) ) AB AB
1 1 1 1 : 120 ms;
3 3 3 3 : 375 ms; 4 4 4 4 : 600 ms.
– 10 –
English