PEUGEOT EnergySaw-254R Manuel D'utilisation page 31

1. To use the saw in mitre saw mode, press the lever (C) Fig. 7 to release the table and move it up. At the end of the table
rotation, you should hear a click.
2. Raise the saw head to the high position. To do so, push the saw head slightly and pull the small round-headed lever (D)
Fig. 8, then give it a quarter turn and let the pins (E) Fig. 9 re-engage.
3. To set the depth stop, move the limiter (N) to the left or right depending on the required depth Fig. 18. Move the limiter
to the right for more depth and to the left for less depth.
4. Put the riving knife back once again using the wing screw (F) Fig. 10 as illustrated in Fig. 19.
5. Turn the cutting height setting lever (J) Fig. 14 fully clockwise (direction opposite the circular saw mode).
6. Fit the dust removal cover (1) Fig. 1 below the saw table, inserting the two black plastic heads (O) Fig. 20.7. If you do not
have an extraction system, attach a dust bag to one of the two extraction nozzles.
You can now use your mitre saw.
OPERATTING THE SAw
IMPORTANT! Before adjusting the saw: switch the saw off, disconnect it from the power source and wait for it come to a
complete stop.
Adjusting the cutting angle:
1. You can adjust the bevel from 0° to 45° to the left thanks to the lock lever (R) Fig. 22. To tilt the saw head to the required
angle, turn the bevel lock lever a quarter turn anticlockwise, tilt the saw head until the required cutting angle is achieved
(use the graduations (S) Fig. 22), then tighten the bevel lock lever by giving it a quarter turn clockwise.
2. To adjust the rotation of the saw head, loosen the screw (T) Fig. 23, then turn the saw head from 0° to 45° to the
left or right. Then re-tighten the screw.
STARTING UP AND STOPPING
in circular table saw mode:
1. To start up the saw, press the green button (U) Fig. 24.
2. To switch off the saw, press the red button (V) Fig. 24.
The saw has an emergency stop push-button.
in mitre saw mode:
1. To start up the mitre saw, press the green button (U) Fig. 24.
2. Press the releasing button (W), while keeping the trigger (X) pushed in Fig. 25. Make sure the blade turns correctly and
release the trigger switch release button.
3. To start cutting, remember to engage the release lever (I) Fig. 11 to release the blade guard and to move the head down.
LENGTHwISE CUTS
1. Adjust the rip fence according to the cutting width required in relation to the saw blade.
2. To assemble the rip fence on the saw table, position the fence support on the rail (Y) and tighten the screw (Z) to lock the
rip fence Fig. 26.
3. Place the workpiece on the support surface, with the wider/flatter side resting on the saw table as illustrated in Fig. 27:
4. Guide broad workpieces by hand along the saw blade, holding them firmly at the left and right.
IMPORTANT! Stay at a safe distance from the saw blade.
BEVEL CUTS
For bevel cutting, the workpiece is cut at an angle of 0° to +45° in relation to the vertical.
1. Make sure the saw table is properly locked.
2. Secure the workpiece firmly with the vice as illustrated in Fig. 28.
3. Release the bevel lock lever and adjust the required bevel angle.
4. Make sure that the riving knife is correctly placed (see Fig. 19) in relation to the saw blade.
5. Tighten the bevel lock lever once again.
6. Start the saw and, using the handle, slowly bring down the saw head onto the workpiece and make the cut. While cutting,
press the saw head on the workpiece, making sure that the rotation speed of the motor does not slow down excessively.
7. Cut the piece in a single movement.
8. After cutting, release the switch and wait for the blade to come to a complete stop.
9. Put the saw head back into its initial position.
CROSS CUTS
1. Insert the mitre fence into one of the slots of the table as illustrated in Fig. 29 and adjust the required angle. Then tighten
the screw (A).
2. Start the saw and, using the mitre fence, slowly guide the workpiece towards the rotating saw blade.
31
30