General Safety Instructions - PEUGEOT EnergySaw-254R Manuel D'utilisation

WARNING !
Read the instructions in full. Any failure to comply with the
instructions listed in this document may lead to electric
shock, fire hazards or serious injury. The term "power tool"
mentioned in all of the warnings listed below refers both
to the power tool when it is connected to the mains (by the
power cord) and when it operates on its battery (without
cables).
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE USE.
1) Work area
a) Keep the work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive atmospheres or in
the presence of flammable liquids, gases or dust. Power tools
generate sparks which may ignite the dust or fumes.
c) Keep onlookers and children away from the work area
while operating a power tool. Distractions can cause you to
lose control of the tool.
2) Electrical safety
a) The power tool plug must correspond to the wall socket.
Do not modify the plug in any event. Do not use an adapter
plug with power tools that must be connected to the earth.
The original plugs and suitable wall sockets reduce the risk
of electric shock.
b) Avoid body contact with earthed surfaces such as piping,
radiators, refrigerators, etc. The risk of electric shock is in-
creased if your body is connected to the earth.
c) Do not expose power tools to rain or humidity. Water ente-
ring a power tool increases the risk of electric shock.
d) Take care of the electrical cord. Never transport, pull or dis-
connect the power tool by pulling on the cord. Keep the cord
away from heat, greasy material, sharp edges and moving
parts. Damaged or tangled cords increase the risk of electric
shock.
e) Only use an extension cord that has been designed for
outdoor use when operating the power tool outdoors. Using
a cord for outdoor use reduces the risks of electric shock.
3) Personal safety
a) Stay alert and watch what you are doing. Use common
sense when operating a power tool. Do not use the power
tool when tired or under the influence of drugs, alcohol or
medication. A moment of inattention can lead to serious
injury.
b) Use personal protective equipment. Always wear protec-
tive goggles. When required, use safety equipment such as
a dust mask, non-skid safety shoes, a hard hat and hearing
protection to reduce the risk of injury.
c) Avoid unintentional starting up. Ensure the switch is in the
off-position before you connect the tool.
Carrying power tools with a finger on the switch or connec-
ting them with the switch set to on can lead to injuries.
d) Remove any adjustment keys or wrenches before starting
up the power.

GENERAL SAFETY INSTRUCTIONS

If a key or wrench remains attached to a moving part, there
is a high risk of injury.
e) Do not bend too far over the tool. Keep your balance and
a proper footing at all times to keep closer control of the
power tool in unexpected situations.
f) Wear appropriate clothing. Do not wear loose clothing
or jewellery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or hair are likely to be
caught by moving parts.
g) If the tool is equipped with a connection for sawdust ex-
haust or dust recovery systems, ensure that they are connec-
ted and used correctly. Using this equipment can reduce the
risks connected to dust.
4) Tool use and care
a) Do not force the power tool. Use the correct power tool
for your application. This will provide better results and will
be safer if the power tool is used at the speed for which it is
designed.
b) Do not use the power tool if it cannot be started up and
stopped using the switch. A power tool that cannot be
controlled by means of the switch is hazardous and must be
repaired.
c) Disconnect the power tool from the mains or remove the
battery before making adjustments, changing accessories or
storing it. These preventive safety measures reduce the risk
of starting the tool accidentally.
d) Store power tools switched off and out of the reach of
children. Do not give them to untrained individuals who
have never used them before and have not read and unders-
tood these instructions. Power tools can be dangerous in the
hands of these individuals.
e) Take care of you power tools. Check the misalignment or
binding
of moving parts, breakage of any parts and any other condi-
tion that could hinder the working of the power tool. If the
tool is damaged, have it repaired immediately. Many acci-
dents are caused by poorly maintained power tools.
f) Keep cutting tools clean and sharpened. Well maintained
cutting tools with sharp cutting edges are less like to bind
and easier to control.
g) Use the power tool, accessories, disc pads, etc. in accor-
dance with these instructions and according to their cha-
racteristics, depending on the task to be carried out and the
working conditions. Using a power tool for reasons other
than those for which it was designed can be dangerous.
5) Repairs
Have your power tool repaired by a qualified technician who
only uses identical spare parts. This is vital in order to ensure
that the power tool can be used safely.
24
23