Milwaukee 6430-20 Manuel De L'utilisateur page 4

WARNING
To reduce the risk of injury,
always unplug tool before changing or
removing accessories. Only use accessories
specifi cally recommended for this tool. Others
may be hazardous.
WARNING
Only use accessories with
maximum speed rating at least as high
as nameplate RPM of tool.
Selecting Blade
Always use sharp blades. Dull blades tend to
overload the tool and increase the chance of
KICKBACK (see "Causes and Operator Prevention
of KICKBACK"). Only use thin kerf blades with a
maximum safe operating speed greater than the no
load RPM marked on the tool's nameplate. Read
the blade manufacturer's instructions before use.
Do not use any type of abrasive cut-off wheel or
dry diamond cutting blades.
Fig. 1
Rip & Crosscut
A multi-purpose blade for ripping, cross cut-
ting and mitering in hardwoods, softwoods,
plywood and composition materials.
Framing-Rip
Designed for fast and accurate ripping along
the grain in hard-or softwoods where a smooth
cross cut is not necessary.
Plywood-Veneer
Recommended for cutting plywood, composi-
tion materials and all types of wood where a
slightly smoother fi nish is needed.
Finish & Trim
Especially designed for cross cutting and
mitering in materials where a very smooth cut
is necessary. Also cuts aluminum.
Installing Blade
1. Unplug tool.
2. To remove blade bolt from spindle, push in
spindle lock button while turning bolt counter-
clockwise with 6 mm hex wrench (provided with
tool) until spindle locks. Remove bolt and outer
blade fl ange.
NOTE: Do not remove inner blade fl ange. Large
diameter of inner fl ange (Fig. 2) should face the
blade.
Inner blade fl ange
Blade
Fig. 2
Outer blade
fl ange
Blade bolt
Spindle
ASSEMBLY
3. Push lower guard lever up to raise lower guard.
Place blade on spindle with teeth pointing the
same direction as the arrow on lower guard.
Release lower guard lever.
4. Place outer blade flange and blade bolt on
spindle.
5. Push in spindle lock button while turning bolt
clockwise with 6 mm hex wrench until spindle
locks. Tighten bolt securely.
6. To remove blade, reverse the above steps. Always
clean dirt and sawdust from spindle, fl anges, up-
per guard and lower guard after use.
Adjusting Depth
1. Unplug tool.
2. To adjust depth of cut, place saw on edge of
workbench and pull up depth adjusting lever.
3. Keeping shoe fl at against workbench, raise or
lower saw to desired position. Lowering saw will
increase depth of cut. Raising saw will decrease
depth of cut. For proper depth setting, blade
should extend no more than 1/4" below material
being cut. Use the depth of cut scale for standard
depths.
4. Push down depth adjusting lever to lock. Check
to be sure depth adjusting lever is secure.
Adjusting Miter Angle
1. Unplug tool.
2. To adjust angle of cut, place saw on edge or
workbench and pull up miter adjusting lever.
3. Hold down shoe and slide saw to desired position
according to markings on miter scale. Positive
stops are located at 0°, 45°, and 56°.
4. To increase the angle of cut above 45° up to 56˚,
push in the 56° override button and tip the saw
to the desired angle.
5. Push down miter lever to lock. Check angle with
a square. Also check to be sure miter adjusting
lever is secure before cutting.
Repositioning Adjustment Levers
The Miter Adjusting Lever and and the Depth
Adjusting Lever can be repositioned to the best
tightening position.
1. Pull out the lever and rotate to the desired posi-
tion.
2. Push in the lever, and press down to lock.
3. Check that the adjustment is secure.
6
Adjusting the Blade to Shoe
The shoe has been adjusted at the factory to a 90
degree setting. Inspect the saw regularly to make
sure the blade is 90 degrees to the shoe.
1. Unplug tool.
2. Set the bevel pointer to zero.
3. To make sure the blade is 90 degrees to the
shoe, place saw on the blade side and retract
lower guard. Place a square against the blade
and shoe to inspect the degree setting (Fig. 3).
4. To adjust the degree setting, loosen the miter
adjusting lever. Turn the bevel adjustment screw
in or out until the blade is at a 90 degree angle
with the shoe.
5. Tighten the miter adjusting lever securely.
WARNING
To reduce the risk of injury,
always unplug tool before attaching or remov-
ing accessories or making adjustments. Use
only specifi cally recommended accessories.
Others may be hazardous.
WARNING
To reduce the risk of injury,
wear safety goggles or glasses with side
shields.
Preventing Kickback
Kickback is the sudden reaction to a pinched blade,
which could cause a saw that is not under control
to lift up and out of the workpiece towards the
user. Take the precautions below to help prevent
kickback.
1. Maintain a fi rm grip and correct body position.
Position arms and body to control the upward and
backward reaction force of kickback (Fig. 4).
Fig. 4
Kickback
2. Keep blades sharp and clean. A sharp blade
will tend to cut its way out of a pinching condi-
tion. A dull blade produces a narrow kerf (path
Fig. 3
Bevel adjustment screw
OPERATION
cut by blade) and is likely to be pinched by the
workpiece. Dull or pitch coated blades also tend
to encourage the user to force the saw, causing
reduced control and blade binding. Any blade
with a small set, even though it is sharp, may
be likely to kick back (Fig. 5).
Set
Fig. 5
Sharp
blade
3. Set the depth of cut for no more than 1/8" to 1/4"
greater than the thickness of the stock (Fig. 6).
The less blade exposed, the less chance of
binding and kickback. Before cutting, be sure
depth and miter adjustments are tight.
Fig. 6
4. Be cautious of pitchy, knotty, wet or warped
stock. These are most likely to create pinching
conditions and possible kickback. Do not rip
warped lumber. Avoid cutting nails.
5. Support workpiece properly. Improperly sup-
ported material can sag or bow, pinching the
blade. When cutting down the center of your
workpiece, support material on both sides of
the cut. Large sheets of thin material such as
paneling, formica, etc. must be well supported
over their entire length (Fig. 7) (see "Cutting
Large Panels"). When cutting the end off of your
workpiece, rest the saw on the supported portion
outside of the supports and allow the cut off end
to fall away (see "General Operation").
7
Dull
blade
⅛"-¼"