Endress+Hauser Liquisys M CCM223 Manuel De Mise En Service page 125
Masquer les pouces
Voir aussi pour Liquisys M CCM223:
- Manuel de mise en service (122 pages) ,
- Information technique (25 pages) ,
- Information technique (23 pages)
Table des Matières
Publicité
Liquisys M CCM223/253
CHECK
Chlorine / ClO2
P
Select contact to
be configured
RELAY
Rel1;
Rel2; Rel3; Rel4
R
Select language
ENG;
SERVICE
ITA; NEL; ESP
S
Rel (= relay)
Main (= mainboard)
Trans (= transmitter)
E+H SERVICE
Contr (= controller)
E
Enter address
HART:
INTERFACE
PROFIBUS: 1 ...
I
Endress+Hauser
Select alarm threshold
monitoring
Off;
Low; High
LoHi; Lo!; Hi!; LoHi!
P1(1)
P111
3-point step controller
Cl2 / ClO2
(only with Rel3 and Rel4)
R2(8)
Clean =
Chemoclean
(only with Rel3 and Rel4)
R2(7)
Timer
R2(6)
PID controller
Cl2 / ClO2
R2(4)
LC °C =
Limit contactor
T
R2(3)
LC PV =
limit contactor
Cl2 / ClO2
R1
R2(1)
Configure Hold
GER; FRA;
S+C = for param. + cal.
Setup = for param.
S1
Module software
SW Version
E1(4)
E141
Module software
SW Version
E1(3)
E131
Module software
SW Version
E1(2)
E121
Instrument software
SW Version
E1(1)
E111
Tag description
0
... 15 or
126
@@@@@@@@
I1
I2
Alarm delay
Set lower
0 min (s)
alarm threshold
0 ... 2000 min (s)
0.00 mg/l
(dep. on F2)
0 ... 19.9 (4.9) mg/l
P112
Switch function R2(8)
Enter setpoint
on or off
0.5 (0.1) mg/l
0 ... 20 (5) mg/l
Off;
On
R281
Switch function R2(7)
on or off
int = internal
ext = external
Off;
On
R271
Define rinse time
Switch function R2(6)
on or off
30 s
0 ... 999 s
Off;
On
R261
Switch function R2(4)
Enter setpoint
on or off
0.5 (0.1) mg/l
Off;
On; Basic; PID+B
0 ... 20 (5) mg/l
R241
Switch function R2(3)
Enter switch-on
on or off
temperature
Off;
On; Basic; PID+B
50 °C
0 ... 50 °C
R231
Switch contact R2(1)
Select switch-on point
on or off
of contact
20 (5) mg/l
0 ... 20 (5) mg/l
Off;
On
R211
Manual Hold
CAL = with Cal.
no
= no Hold
Off;
On
S2
Hardware version
Serial number
is displayed
HW Version
E142
Hardware version
Serial number
is displayed
HW Version
E132
Hardware version
Serial number
is displayed
HW Version
E122
Hardware version
Serial number
is displayed
HW Version
E112
Set upper
alarm threshold
20.00 (5.00) mg/l
Off;
0.1 ... 20 (5) mg/l
P113
P114
Enter control
Enter integral action time
gain K p
T n (0.0 = no I comp.)
1.00
0.01 ... 100.00
0.0 min
R282
R283
Select start pulse
Enter pre-rinse time
i+ext = internal + external
i+stp = int. w. suppression by ext.
R272
Define pause time
360 min
1 ... 7200 min
R262
R263
Enter control
Enter integral action time
gain K p
T n (0.0 = no I comp.)
1.00
0.01 ... 100.00
0.0 min
R242
R243
Enter switch-off
temperature
50 °C
0 ... 50 °C
R232
R233
Select switch-off point
of contact
20 (5) mg/l
0 ... 20 (5) mg/l
R212
R213
Enter Hold
Enter SW upgrade
dwell time
release code (Plus pack.)
10 s
0 ... 999 s
S3
S4
Module identification
is displayed
E143
E144
Module
identification
is displayed
E133
E134
Module
identification
is displayed
E123
E124
Module
identification
is displayed
E113
E114
Annexe
Select process
monitoring
AC; CC; AC CC
AC!; CC!; ACCC!
P115
0.0 ... 999.9 min
R284
20 s
0 ... 999 s
R273
Define minimum
pause time
120 min
1 ... 3600 min
R264
0.0 ... 999.9 min
R244
Set pick-up
delay
0 s
0 ... 2000 s
R234
Set pick-up
delay
0 s
0 ... 2000 s
R214
0
0 ... 9999
S5
A0002635-FR
125
Publicité
Table des Matières
