STAMOS S-LS-2 Manuel D'utilisation page 13

6103: S-LS-4
SMD REWORK STATION 6103: S-LS-4 OPERATION:
1. Device must be placed on stable work table, SMD rework gun must be placed into the holder.
2. Fix the appropriate nozzle and connect the device to the power source.
3. Turn on the device with the main switch placed at the back of the device, turn on the SMD rework gun with switch
(1), gun will start to heat.
4. Set the desired temperature using buttons (8).
5. Setting the desired airflow volume: set the desired airflow volume using airflow volume adjustment knob.
6. After work, the SMD rework gun should be placed into the holder. Turn off the SMD rework by switch (1).
7. If the device is not using for a long time, it should be completely disconnected from the power source.
SOLDERING STATION 6103: S-LS-4 OPERATION:
1. Device must be placed on stable work table, soldering iron must be placed into the holder.
2. Fix the appropriate soldering tip and connect the device to the power source.
3. Turn on the device with the main switch placed at the back of the device, turn on the soldering iron with switch (4),
it will start to heat.
4. Set the desired temperature using temperature adjustment knob (5). Soldering iron heater indicator (6) will light up.
When the indicator will be flashing regularly, the desired temperature has been reached and it is constant, and the
soldering iron is ready to work.
5. After work, the soldering iron should be placed into the holder. Turn off the soldering station by switch (4).
6. If the device is not used for a long time, it should be completely disconnected from the power source.
If the display is showing the „---„ it means that the output temperature is lower than 100 ⁰C, SMD rework station is
GENERAL REMARKS
1.
in stand by mode, SMD rework gun is placed in the holder.
2. if the display is showing "S-E" it means that soldering iron is disconnected, and HOT AIR gun is having problem with
the heat sensor.
3. When the device is being turned on, both soldering iron and HOT AIR gun should be placed in their holders.
4. The outlet of the SMD rework gun should be clean and free from any obstacles.
5. When using small nozzles, it should be remembered that the air flow should be suitable to the diameter of the fixed
nozzle. In order to avoid any SMD rework gun damages, too high air flow along with the high temperature mustn't be
used for a long period of time.
6. Depending on user's needs, different air flow settings may cause slight variations in temperatures value. The minimum
distance between the outlet of the HOT AIR gun and the subject is 2 mm.
7. Good ventilation of the room in which the appliance is used must be provided. In addition, the device should be placed
in a location with good air circulation to dissipate heat.
8. NOTE: It is forbidden to cover the air intake holes on the handle of a SMD rework gun during work. This may cause
serious damages of the fan and the heater!
SAFETY ISSUES REMARKS
1. Nozzles should be installed without the use of excessive force, also do not use the pliers or tweezers. Do not over
tighten the mounting screws of the nozzle.
2. Tips and nozzles can be changed when the SMD rework gun and the soldering iron are completely cold.
3. It is forbidden to use the device near the flammable or combustible elements and objects or at similar places. Tips and
nozzles as well as the air coming out of the HOT AIR gun have very high temperature, it is forbidden to touch these
elements as well as it is forbidden to put the hot air directly to face or body. This can cause serious burns.
4. After long time of use, the outlet of SMD rework gun may be covered with some dust. The outlet should be cleaned
on a regular basis in order to ensure undisturbed air flow.
5. Too high temperature of the soldering iron may be the cause of reduction of the functionality of the soldering tips.
6. Soldering iron tip must be cleaned regularly using sponge and plate on a layer of tin to prevent tips oxidation.
EN DE
13