Technical Data; Safety Rules - EINHELL E-BH 950 Mode D'emploi

Anleitung E-BH 950 SPK 7
1. Layout (Fig. 1)
1 Dust guard
2 Locking sleeve
3 On/Off switch
4 Additional handle
5 Drilling depth stop
6 Hammer stop
7 Rotation stop

2. Technical data

Mains voltage: 230 V ~ 50 Hz
Power:
Idle speed:
Hammer rate: 3675 min
Drilling capacity (max.): Concrete/Stone 32 mm
Weight:
Vibration: 11,51 m/s
Sound pressure level:
Sound power level:
Protection class:
The noise and vibrations from this tool were measu-
red in accordance with EN 50144-2-6. This hammer
drill is not intended for use outdoors as defined in
Article 3 of the Directive 2000/14/EC.

3. Safety rules

The corresponding safety information can be
found in the enclosed booklet.
4. Preparations
Use a detector to localize pipes and/or cables in
walls with concealed electric, water or gas lines.
Before you plug in the machine, check that your
mains voltage is the same as that marked on the
rating plate.
4.1 Proper use
The tool is designed for drilling with hammer action in
concrete, rock and brick, as well as for chiseling
work, always using the correct drill or chisel bit.
4.2 Fitting and changing a bit (Fig. 2)
Clean the bit and coat it with a little machine
grease before you insert it.
Pull back the locking sleeve (A) and hold in this
position.
06.04.2004 12:23 Uhr
Insert the dust-free bit with a twist as far as it
goes into the chuck. The bit will automatically be
locked in place.
Pull on the bit to check that it is secure.
4.3 Removing a bit (Fig. 3)
Pull back the locking sleeve (A), hold and pull out the
bit.
5. Starting up (Fig. 1 - Pos. 3)
5.1 Switching on/off
Switching on: Press On/Off switch (3).
950 Watt
Switching off: Release On/Off switch (3).
700 min -1
5.2 Additional handle (Fig. 1 - Pos. 4)
-1
For safety reasons you should always use the
hammer drill with the additional handle.
For a secure posture during work you should turn the
5,9 kg
additional handle. Twist the additional handle anti-
2
clockwise and turn.
Then fix the additional handle by twisting again.
94 dB(A)
106 dB(A)
5.3 Depth stop (Fig. 1 – Item 5)
® / II Slacken the thumb screw on the additional handle
and insert the straight part of the depth stop into the
hole in the additional handle. Set the depth stop and
retighten the thumb screw.
5.4 Dust collector (Fig. 4)
Before you start any hammer drilling work directly
over your head, slide the dust collector on the bit.
5.5 Hammer stop (Fig. 5)
The hammer drill comes with a hammer stop for
smooth pre-drilling.
Turn the lever switch (6) to the right to position
(b) to switch off the hammer mechanism.
To turn the hammer mechanism back on you
have to turn the lever switch (6) back to position
(a).
5.6 Rotation stop facility (6)
The rotation function of the hammer drill can be swit-
ched off for chiseling jobs.
To do so, press the button (d) on the lever selec-
tor (7) and turn the lever selector (7) so that the
mark (c) coincides with the arrow (a) on the
machine housing.
To reactivate the rotating function you must again
press the button (d) on the selector lever (7) and
turn the lever selector (7) so that the mark
coincides again with the arrow (a).
Seite 7
GB
(b)
7