Manual Defrost; Cleaning, Care & Maintenance; Cleaning The Condenser - Polar G604 Mode D'emploi

UK
Parameter Name
Defrost Cycle Time
d8
Intervals
Maximum Defrost
d9
Duration
Defrost Cut-off
d10
Temperature
Additional Cut-off
d11
Defrost Period
Delayed Actual
d12
Temperature Display
Compressor On/Off
d13
During Defrost
Evaporator Drying
d14
Time
=19 Temperature Offset
=22 Unit of Measurement
Compressor Operation
=23
During Probe Failure
Compressor 'On'
=24
Duration
Compressor 'Off'
=25
Duration
Initial Defrost After
=34
Startup
Minimum
=38
Temperature Alarm

Manual Defrost

The appliance will automatically run a defrost cycle every six hours.
Note: The cycle starts from the time the appliance is initially powered up.
To manually defrost the appliance:
Press and hold the DEFROST
1.
The defrost cycle will start immediately and the Defrost LED illuminates. The defrost will last a maximum of 30 minutes.
2.
Note: Starting a manual defrost also resets the automatic defrost timer.
The next automatic defrost will start six hours after the manual defrost has finished.
Waste water is collected in the waste water tray.
3.
Cleaning, Care & Maintenance
• Switch off and disconnect from the power supply before cleaning.
• Clean the interior of the appliance as often as possible.
• Do not use abrasive cleaning agents. These can leave harmful residues.
• Clean the door seal with water only.
• Always wipe dry after cleaning.
• Do not allow water used in cleaning to run through the drain hole into the evaporation pan.
• Take care when cleaning the rear of the appliance. Sharp edges can cut.
• A POLAR agent or qualified technician must carry out repairs if required.

Cleaning the Condenser

Periodically cleaning the condenser can extend the life of the appliance.
POLAR recommend that a POLAR agent or qualified technician clean the condenser.
3
Description
Set the time between each defrost cycle
Set the maximum length of the defrost cycle
Note: The defrost duration can be overridden by parameter d10
(below), if the cut-off temperature is reached before the end of the
defrost duration
Set the defrost cut-off temperature
Set an additional amount of defrost time after the defrost cut-off point has
been reached (if required)
Set the length of time the inner temperature of the appliance (before defrost
started) is displayed for after a defrost cycle has finished
Turn the Compressor On or Off during the defrost cycle
Set the amount of time the compressor remains turned Off after a defrost
cycle, reducing the amount of frost build up
Should there be any variance between measured and actual temperature, the
measured temperature can be offset to compensate
Set whether the temperature is displayed in Centigrade or Fahrenheit
Set whether the compressor runs or remains Off during a temperature probe
failure
Set the length of time the compressor runs during a temperature probe failure 1-99 minutes
Set the length of time the compressor remains Off during a temperature
probe failure
Set whether the appliance starts a defrost cycle 10 minutes after startup or
after the time programmed in parameter d8 (Defrost Cycle Time Intervals)
Set the display to flash should the inner temperature of the appliance drop
beyond a specified point from the programmed operating temperature
button for 5 seconds.
Range
1-999 hours
0-999 minutes
-45°C to 50°C
0-99 minutes
0-99 minutes
On (1) or Off (0)
0-99 minutes
-20°C to 20°C
Centigrade (0) or Fahrenheit (1)
Compressor runs (1)
Remains Off until fault fixed (0)
Runs intermittently with parameters
=24 and =25 (2)
1-99 minutes
Begins 10 minutes after startup (0) or
when programmed (1)
1°C to 50°C
Default
Parameter
Value
6
30
n/a
n/a
30
n/a
0
-3°C
0
2
10
10
n/a
30°C