Optional Accessories; Use And Maintenance - Atag WS9011FM Mode D'emploi Et D'installation

• INSTALLATION OF MODELS WITHOUT DECORATIVE
DUCTS
EXTRACTOR HOOD
- Remove the 4 screws B as shown in (Fig.9A).
- Remove both grid E on the air outlet hole and lid M as
shown in (Fig.9B).
- Connect the hood to the flexible hose (not supplied)
and the hose to the air exhaust hole previously prepared
(Fig.9C).
- Fix the lid once again by using the 4 screws previously
removed in (Fig.9A).

• OPTIONAL ACCESSORIES

This model may have decorative ducts as optional
accessories - ask your retailer for information.
Before fixing the decorative ducts, remove both the 4
screws B and lid M, as shown in (Fig.10A-B).
A sound-absorbing kit is also available (to be ordered as
an OPTIONAL accessory) in order to increase the
quietness level of the hood. The sound-absorbing layer
must be applied to the back of the decorative panel. For
fixing operations, refer to the instructions supplied with
the kit.
• INSTALLATION OF MODELS WITH DECORATIVE DUCTS
Make sure the electrical power supply is within the
measurements of the decorative connector.
Adjust the width of the support bracket of the top
connector (Fig.11C). Then fix it to the ceiling so that it is
on the same axis as the hood using screws A (Fig.11C)
adhering to the distance from the ceiling shown in
(Fig.11B). Connect flange C to the air exhaust hole using
flexible hose L (Fig.11D).
Slide the top duct into the bottom duct. Fix the bottom
duct to the hood using screws B (supplied) (Fig.11E).
Pull out the top duct as far as the bracket and fix it using
screws F (Fig.11C).
• FILTER HOOD
In order to change an EXTRACTOR HOOD into a FILTER
HOOD, remove the bracket from the package
and fix it using the 6 screws supplied - as shown in
Fig.14.
Order the filters as accessories from your retailer.
To replace the active carbon filters pull lever B outwards
as shown in (Fig.10).

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to
cooking.
It is recommended to leave the appliance in operation for
15 minutes after cooking is terminated in order to com-
pletely eliminate cooking vapours and odours.
The proper function of the cooker hood is conditioned by
the regularity of the maintenance operations, in particu-
lar, the active carbon filter.
• The anti-grease filters capture the grease particles
suspended in the air, and are therefore subject to clog-
ging according to the frequency of the use of the appli-
ance.
In order to prevent fire hazard, it is recommendable to
clean the filter at a maximum of 2 months by carrying out
the following instructions:
- Remove the filters from the cooker hood and wash them
in a solution of water and neutral liquid detergent, leaving
to soak.
- Rinse thoroughly with warm water and leave to dry.
- The filters may also be washed in the dishwasher.
The aluminium panels may alter in colour after several
washes. This is not cause for customer complaint nor
replacement of panels.
• The active carbon filters purify the air that is replaced
in the environment. The filters are not washable nor re-
useable and must be replaced at maximum every four
months. The saturation of the active carbon filter de-
pends on the frequency of use of the appliance, by the
type of cooking and the regularity of cleaning the anti-
grease filters.
• Clean the fan and other surfaces of the cooker hood
regularly using a cloth moistened with denatured alcohol
or non abrasive liquid detergent.
• The illumination installation is designed for use during
cooking and not for prolonged general illumination of the
environment. Prolonged use of the illumination installa-
tion notably reduces the duration of the bulb.
COMMANDS: (Fig.12)
Push-button A = on/off lights switch
Push-button B = on/off cooker hood switch. The appli-
ance switches on at speed level 1, If the cooker hood is
on depress the push-button for 2 sec. to switch off the
cooker hood. If the cooker hood is at speed level 1 it will
not be necessary to depress the push-button to switch
the cooker hood off. Decreases the motor speed.
Display C = indicates the motor speed level selected
and activates the timer.
Push-button D = switches on the cooker hood. Increases
the motor speed. Touching the key at 3rd speed, the
intensive function runs for 10', then the appliance go
back to work at the original speed. During this function
the display blinks.
Key E = The Timer times the functions on activation for
15 minutes, after which they are switched off. The Timer
is deactivated by re-pressing Key E. When the Timer is
activated the decimal point must flash on the display.
The Timer cannot be activated if the intensive speed is
functioning.
The "clean air" function is activated by pressing key E
for 2 seconds when the appliance is switched off. This
switches the motor on for 10 minutes every hour at the
first speed. During functioning a rotary movement of the
peripheral segments must be visualised on the display.
When this time has passed the motor switches off and
the fixed letter "C" must be visualised on the display
until the motor re-starts after 50 minutes for another 10
minutes and so on. Press any key apart from the light
keys to return to normal functioning. Press key E to
deactivate the function.
• Active carbon/grease filter saturation:
- When display item C flashes, at a speed where it
alternates with the letter F (e.g. 1 and F), the grease
filters must be washed.
- When display item C flashes, at a speed where it
alternates with the letter A (e.g. 1 and A), the carbon
filters must be replaced.
After the clean filter has been positioned correctly, the
electronic memory must be reset by pressing button A
for approximately 5 seconds, until the indication F or A
shown on the display C stops flashing.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING
THE ABOVE WARNINGS.
- 14 -