Cleaner Maintenance - Hoover Chorus CH40PAR 011 Manuel D'utilisation

The other nozzles are accessories for specialist cleaning tasks and are recommended
for occasional use only.
It is important to note that this vacuum cleaner is supplied with an Energy Label as
required by European Regulation (EU) 665/2013.
If the label shows a red prohibition circle on the left covering the carpet symbol, then this
indicates that the vacuum cleaner is not suitable use on carpets.
If the label shows a red prohibition circle on the right covering the hard floor symbol, then
this indicates that the vacuum cleaner is not suitable for use on hard floors.
#1
NOTE: Dust pick up ability carpet, dust pick up ability hard floor, and energy efficiency
in accord with Commission Regulations (EU) 665/2013 and (EU) 666/2013.
All accessories can be fitted to the end of the hose handle or the end of the tube.
2 in 1 Accessory – Combines several functions into one tool: [T]
Crevice Tool – For corners and hard to reach areas.
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas.
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hair removal. [U]
Allergen Remover Mini Turbo Nozzle* –
deep cleaning on textile surfaces and other hard to clean areas. Particularly suitable for
allergen removal. [V]
Parquet Nozzle * - For Parquet floors and other delicate floors. [W]
IMPORTANT: Do not use the Mini Turbo nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle station ary while the brush is rotating.

CLEANER MAINTENANCE

Emptying the Dust Container
When the dust reaches the max level indicator in the container, empty the dust container.
IMPORTANT: To maintain optimum performance do not allow the dust to sit higher than
the max level.
1. Turn the cleaner off switching the on/off pedal and unplug the power cable.
2. Press the dust container release button and remove the dust container assembly
from the cleaner. [12]
3. Hold the dust container with one hand, and remove the dust container lid by rotating
anti-clockwise. [13]
4. Remove the pre-motor filter assembly from bin assembly. [14]
*Certain Models Only ** Certain models only, nozzles may vary according to model
Use the mini turbo nozzle on stairs or for
5. Remove the Vortex Finder from bin assembly. [15]
6. Empty the dust from the bin. [16]
7. Refit the vortex finder and pre-motor filter assembly to bin assembly.
8. Refit the dust container lid to bin assembly.
9. Close and refit to the cleaner main body.
Cleaning the washable filters
The cleaner is fitted with pre-motor filter and exhaust filters. To maintain optimum cleaning
performance, regularly remove the filters and tap against the side of the dust container to
release dust. The filters should be washed every 5 cassette empties or when the filters
have excessive dust level.
IMPORTANT: All bagless cleaners require regular filters cleaning. Failure to clean your
filters may result in air blockage, overheating and product failure. This may invalidate
your guarantee.
IMPORTANT: Regularly check and maintain the filters.
IMPORTANT: Always ensure the filter pack is fully dry before use.
To access the pre-motor filter:
1. Remove the dust container from the cleaner. [12]
2. Hold the dust container with one hand, and remove the dust container lid by rotating
anti-clockwise. [13]
Remove the pre-motor filter assembly from dust container assembly. [14]
3.
4. Gently tap and wash the pre-motor filter. Do not use hot water or detergents.
Remove excess water from the filter and leave to dry fully before re-using. [19,20]
5. Reassemble the pre-motor filter assembly once fully dry and refit it into the cleaner.
To access the exhaust filter:
1. Unclip the exhaust filter cover from the rear of the cleaner main body. [17]
2. Remove the exhaust filter from the rear of the cleaner. [18]
3. Gently tap and wash the filter using warm water. Do not use hot water or detergents.
Remove excess water from the filter and leave to dry fully before re-using.
[19,20]Refit the exhaust filter to the rear of the cleaner once fully dry and refit the
exhaust filter cover.
IMPORTANT: Do not use the product without the filter pack fitted.
Cleaning the dust container / separation unit
This cleaner uses a separation system unique to Hoover. If necessary the separation unit
can be disassembled from the dust container and cleaned.
1. Press the dust container release button and remove the dust container assembly
from the cleaner. [12]
3
GB