Eu Declaration Of Conformity; Transportation And Storage; Inspect The Delivery; Transportation Guidelines - Xylem LOWARA Resiboost MMW09 Manuel D'installation, D'utilisation Et D'entretien

1.6 EC Declaration of Conformity
Xylem Service Italia S.r.l., with headquarters in Via
Vittorio Lombardi 14 - 36075 Montecchio Maggiore
VI - Italy, hereby declares that the product
Control device ResiBoost
er (frequency converter) for electric pumps
(see label on first page)
fulfills the relevant provisions of the following Euro-
pean directives
• Low Voltage 2006/95/EC (year of first use of the
mark: 2015)
• Electromagnetic compatibility 2004/108/EC
and the following harmonised technical standards
• EN
60730-1:2000+A12:2003+A13:2004+A1:2004+
A14:2005+A16:2007+A2:2008, EN
60730-2-6:2008
• EN 61800-3:2004+A1:2012
Montecchio Maggiore,
30.07.2015
Amedeo Valente
(Director of Engineering
and R&D)
rev.00

1.7 EU Declaration of Conformity

1. Unique identification of the EEE: No.
MMW/MTW/MMA/ MTA
2. Name and address of the manufacturer:
Xylem Service Italia S.r.l.
Via Vittorio Lombardi 14
36075 Montecchio Maggiore VI
Italy
3. This declaration of conformity is issued under
the sole responsibility of the manufacturer.
4. Object of the declaration: Control device Resi-
™
Boost with variable speed driver (frequency
converter) for electric pumps (see label on first
page)
5. The object of the declaration described above is
in conformity with Directive 2011/65/EU of the
European Parliament and of the Council of 8
June 2011 on the restriction of the use of certain
hazardous substances in electrical and elec-
tronic equipment.
6. Harmonised standards used: -
Technical specifications used: -
7. Additional information: -
Signed for and on behalf of:
Xylem Service Italia S.r.l.
Via Vittorio Lombardi 14
36075 Montecchio Maggiore VI
Italy
Montecchio Maggiore, 30.07.2015
Amedeo Valente
(Director of Engineering
™
with variable speed driv-
and R&D)
rev.00
Lowara is a trademark of Xylem Inc. or one of its
subsidiaries.

2 Transportation and Storage

2.1 Inspect the delivery

1. Check the outside of the package.
2. Notify our distributor within eight days of the de-
livery date, if the product bears visible signs of
damage.
3. Open the carton.
4. Remove packing materials from the product.
Dispose of all packing materials in accordance
with local regulations.
5. Inspect the product to determine if any parts
have been damaged or are missing.
6. Contact the seller if anything is out of order.

2.2 Transportation guidelines

Precautions
WARNING:
• Observe accident prevention regula-
tions in force.
• Crush hazard. The unit and the com-
ponents can be heavy. Use proper
lifting methods and wear steel-toed
shoes at all times.
Check the gross weight that is indicated on the
package in order to select proper lifting equipment.
Position and fastening
The unit must be transported only in its horizontal
position as indicated on the package. Make sure that
the unit is securely fastened during transportation
and cannot roll or fall over. The product must be
transported at an ambient temperature from -10°C to
70°C (14°F to 158°F) with a non-condensing humidi-
ty of <95% and protected against dirt, heat source,
and mechanical damage.

2.3 Storage guidelines

2.3.1 Storage location
NOTICE:
• Protect the product against humidity, dirt, heat
sources, and mechanical damage.
• The product must be stored at an ambient tem-
perature between 10°C and 70°C (14°F and
158°F) and a non-condensing humidity below
95%.
• The converter uses electrolytic capacitors which
can deteriorate when not used for a long period
of time. If storing for a year or more, make sure
to run them occasionally to prevent deterioration.

3 Product Description

3.1 Product overview

en - Original instructions
25