cecotec CONGA 7090 Manuel D'instructions page 21

ENGLISH
Warning: Do not expose the charging base to direct sun light.
Long press the power button for 3 seconds; when the light indicator turns on, place the robot
on the charging base.
Fig. 10.
Steady blue light: ON/operating
Oscillating orange light: Charging
Red light blinks: Error
Note:
Take the robot to the charging base if the battery is low. The robot might not turn on if the
battery is very low.
The robot will automatically turn on when placed on the charging base.
The robot cannot be turned off during charging.
Wet & dry tank installation
Note: It is not suggested to use the scrubbing function for the first-time use.
Open the tank's blue silicone lid, fill the tank with water carefully so water does not come out
and close it again. Make sure the silicone clip is properly closed to avoid water from pilling.
Fig. 11.
Install the tank in the robot following the indicated direction. Make sure the clip is properly
fastened.
Fig. 12.
Only for Wet & dry tank installation:
Attach the mop to the bottom part of the mop bracket with the Velcro.
Fig. 13.
Manually press the tabs on both sides of the Wet & dry tank and push it into its correct
position. You will hear a click when it is properly fixed.
Fig. 14.
Recommendations:
Do not use the scrubbing function while the robot is unattended.
Remove the mop bracket when the robot is charging or not in use.
If there are carpets in the house, set Restricted Areas to avoid the robot from passing over
them.
Add some drops of cleaning agent (not corrosive) if considered necessary.
To remove the mop bracket, press the release button and pull from it outwards.
Warnings:
Using cleaning agents in excess might block water outlets.
In order to achieve perfect scrubbing, it is suggested to moisten the mop before using it.
38
7090
First cleaning
Once the robot and the charging base are completely installed, follow these steps before
scheduling the first cleaning cycle.
First of all, the robot must be fully charged. It is suggested to allow the robot to charge
overnight. When it is fully charged, it may carry out the first cleaning cycle and save the first
map. To do so, activate Auto cleaning mode and Eco power level. It is very important to follow
these indications for the robot to recognize each and every corner in the house and to create
a complete map.
If the house where the robot is going to be used is too big and the robot runs out of battery,
do not worry. The robot returns to the charging base, saves the full map and those that have
not been completed, and once it is charged again, it resumes the cleaning cycle from the
point it has stopped until it maps the whole surface. The robot keeps on mapping constantly,
therefore it adapts independently to each house's features and continuously improves
previous maps.
4. OPERATION
Once the robot's light indicator changes from oscillating orange to steady blue, the battery is
fully charged, and the robot is ready to operate.
The robot cannot operate with low battery.
Recommendations: Remove all cables and obstacles from the floor before operating the
robot in order to avoid accidents and damage.
Robot buttons
Fig. 15.
Auto mode
Press the power button on the robot for it to start cleaning automatically, first a cleaning
cycle in Edge mode and then another cycle in and organised zigzag motion, recognising which
areas it has cleaned and which ones it has not. The robot will automatically plan the cleaning
route as it is cleaning. If during this mode the robot is controlled manually, the robot will
calculate the route again and could go through previously cleaned areas. In order to ensure
efficient cleaning, do not operate it manually during auto mode cleaning.
Thanks to its Total Surface 3.0 technology, if the battery is low during the cleaning cycle, the
robot will smartly return to the charging base automatically and, once it is fully charged, it
will resume the cleaning process from the same point, offering a high-efficiency cleaning.
In order to optimise the whole process, the robot will automatically calculate the necessary
charging time according to the surface to be cleaned. During cleaning, the robot will stop
briefly to evaluate the area and calculate the cleaning route (this stop will vary depending on
the house conditions).
ENGLISH
39
7090