Installing The Water Line; What You Will Need - Hotpoint 20 Manuel D'utilisation Et D'installation

INSTALLING THE WATER LINE

BEFORE YOU BEGIN
Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of tubing
you need. Approved plastic water supply lines are GE
SmartConnect Refrigerator Tubing (WX08X10002,
™
WX08X10006, WX08X10015 and WX08X10025).
When connecting your refrigerator to a GE Reverse Osmosis
Water System, the only approved installation
is with a GE RVKit. For other reverse osmosis water systems,
follow the manufacturer's recommendations.
If the water supply to the refrigerator is from a Reverse
Osmosis Water Filtration System AND the refrigerator also
has a water filter, use the refrigerator's filter bypass plug.
Using the refrigerator's water filtration cartridge in
conjunction with the RO filter can result in hollow ice cubes
and slower water flow from the water dispenser.
This water line installation is not warranted by the
refrigerator or icemaker manufacturer. Follow these
instructions carefully to minimize the risk of expensive water
damage.
Water hammer (water banging in the pipes) in house
plumbing can cause damage to refrigerator parts and lead to
water leakage or flooding. Call a qualified plumber to correct
water hammer before installing
the water supply line to the refrigerator.
To prevent burns and product damage, do not hook
up the water line to the hot water line.
If you use your refrigerator before connecting the water line,
make sure the icemaker power switch is in the OFF position.
Do not install the icemaker tubing in areas where
temperatures fall below freezing.
All installations must be in accordance with local plumbing
code requirements.
WARNING –
supply only.

WHAT YOU WILL NEED

• Copper or GE SmartConnect
1/4" outer diameter to connect the refrigerator to the
water supply. If using copper, be sure both ends of the
tubing are cut square.
To determine how much tubing you need: measure
the distance from the water valve on the back of the
refrigerator to the water supply pipe. Be sure there is
sufficient extra tubing to allow the refrigerator to move out
from the wall after installation.
GE SmartConnect Refrigerator Tubing Kits are available
™
in the following lengths:
2' (0.6 m)
– WX08X10002
6' (1.8 m)
– WX08X10006
15' (4.6 m)
– WX08X10015
25' (7.6 m)
– WX08X10025
Installation Instructions
Connect to potable water
Refrigerator Tubing kit,
™
WHAT YOU WILL NEED
NOTE: The only GE approved plastic tubing is that
supplied in GE SmartConnect™ Refrigerator Tubing kits.
Do not use any other plastic water supply line because the
line is under pressure at all times. Certain types of plastic
will crack or rupture with age and cause water damage to
your home.
• A GE water supply kit (containing tubing, shutoff valve
and fittings listed below) is available at extra cost from
your dealer or from Parts and Accessories,
800.626.2002.
• A cold water supply. The water pressure must be between
20 and 120 p.s.i. (1.4–8.2 bar) on models without a water
filter and between 40 and 120 p.s.i. (2.8–8.2 bar) on
models with a water filter.
• Power drill.
• 1/2" or adjustable wrench.
• Straight and Phillips blade screwdriver.
• Two 1/4" outer diameter compression nuts and
2 ferrules (sleeves)—to connect the copper tubing
to the shutoff valve and the refrigerator water valve.
OR
• If you are using a GE SmartConnect™ Refrigerator
Tubing kit, the necessary fittings are preassembled to the
tubing.
• If your existing copper water line has a flared fitting at
the end, you will need an adapter (available at plumbing
supply stores) to connect the water line to the refrigerator
OR you can cut off the flared fitting
with a tube cutter and then use a compression fitting. Do
not cut formed end from GE SmartConnect™
Refrigerator tubing.
• Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with a
minimum inside diameter of 5/32" at the point of
connection to the COLD WATER LINE. Saddle-type
shutoff valves are included in many water supply kits.
Before purchasing, make sure a saddle-type valve complies
with your local plumbing codes. Install the shutoff valve
on the nearest frequently used drinking water line.
11
(CONT.)