Blaupunkt Phoenix MP33 Notice D'emploi Et De Montage page 8

Radio Reception
Seek Tuning
1.
BAND
Press the to select the desired AM or FM band.
FM 1 ➜ FM 2 ➜ FM 3 ➜ AM 1 ➜ AM 2
(FM 3 & AM 2 are Travel Store bands.)
2.
Rotate the TUN/TRK dial to tune in stations. Tuning au-
tomatically stops at a broadcasting frequency.
When tuned in to FM stereo broadcasting stations, the
" " stereo signal indicator will appear on the display
window.
- -
: .
Lower Frequency
TUN TUN
/TRK /TRK
: .
Higher Frequency
+ +
Manual Tuning
1.
Press the BAND to select the desired AM or FM band.
2.
Rotate and hold the TUN/TRK dial for more than 0.5 sec-
ond to activate the manual tuning mode.
n
" MA " indicator will appear on the sub display.
Rotate again to tune in to stations.
After 4 seconds of completing Manual Tuning, the tuning
control will revert to the Seek Tuning mode.
phnx33_body 7
Scan Tuning
1.
Press the BAND to select the desired AM or FM band.
2.
Hold the SC/PS pressed for less than 2 seconds.
The unit will scan the selected band for stations and the
unit will stop at each receivable station for 10 seconds,
before continuing to the next station.
SC/PS
Press the again to stop Scan Tuning and remain
this on the selected frequency.
Preset Scan Tuning
1.
Press the BAND to select the desired AM or FM band.
2.
SC/PS
Hold the pressed for more than 2 seconds.
The unit will scan preset memory for the 12 stations from
the AM 1/AM 2 band or the 18 stations from the FM 1/FM
2/FM 3 bands. The unit will stop at each receivable pre-
set station for 10 seconds, before continuing to the next
preset station.
Press the SC/PS again to stop Preset Scan Tuning and
remain this on the selected frequency.
Memorizing Stations Automatically (Travel
Store)
1.
Press the BAND to select the desired AM or FM band.
2.
Hold the BAND pressed for longer than 2 seconds.
Up to 6 stations will be automatically stored in preset
memory for the selected band.
If the radio is in FM 1 or FM 2, it switches to FM 3. If the
radio is in AM 1, it switches to AM 2.
Note
This function is available for FM 3 and AM 2.
Memorizing Only the Desired Stations
You can store up to 6 stations on each band (18 for FM 1, FM
2 and FM 3, 12 for AM 1 and AM 2) in the order of your choice.
1.
Press the BAND to select the desired band.
2.
Rotate the TUN/TRK dial to tune in stations.
3.
Press and hold the desired preset memory button
6
for about 2 seconds until the frequency indicator
flashes twice.
The number of the pressed preset memory button ap-
pears on the display window.
Note
If when you store another station on the same preset number
button, the previously stored station is replaced with new one.
Receiving the Memorized Stations
1.
Press the BAND to select the desired AM or FM band.
2.
6
Press the 1 - momentarily.
Local/Distant (LO/DX) Selection
This feature is used to select the signal strength at which the
radio will stop during Seek Tuning.
MUTE / SENS
Press the for more than 2 seconds to select the
Local setting and only strong (local) stations will be received.
The " SENS LO " appears on the display window.
Pressing for more than 2 seconds again will select the Dis-
tant setting and the radio will stop at a wider range of signals,
including weaker more distant stations. The " SENS DX " ap-
pears on the display window. DX is the suggested default
setting.
03/4/22, 17:37
1 -
E-7