Witter HY63U Instructions De Montage

MATERIALS:
A 1 Crossbar.
C 1 L/H Sidearm.
D 1 R/H Sidearm.
E 4 M12 x 35 x 1.25 fine pitch Bolts & lock washers.
F 4 M12 x 35 x 1.25 fine pitch Bolts, lock washers and Nuts.
G 2 Adhesive foam strip.
J 2 Bumper Support Angle.
K 2 Bumper Support Plate.
L 2 M8 x 20 x 1.25 Bolt, Washers & Nyloc Nuts.
ZN Neck option.
CB 2 M16 x 45 x 2.0 Bolts.(for use with Fixed neck option if standard bolts are close to bumper)
Note: This towbar must be used with either a Witter Towball (part number Z11) or Class A50-1 or A50-X towball, which dimensionally conforms to
A50-1 with a 'D' and 'S' value greater than or equal to that of the towbar.
FITTING:
1. Remove plastic under tray left hand side 6 off fixings. Remove inner plastic wheel arch guards, 5 off screw type fixings lower side of
either wheel arch, and also nut type fixings holding wheel arch liner in place for easy access to chassis mountings both sides.
Lowering the exhaust from its' rubbers will also ease fitment.
2. Standard i20: Remove Lower bumper trim, fixings along bottom edge and in wheel arches then continue to point 5.
3. i20 Active: Remove the bumper. Remove light clusters by carefully prying off a plastic cover to reveal screws. Remove screws and
free clusters by pulling rearward. Remove the plastic fixing in the top face of the bumper. Remove screws and plastic fixings within
the wheel arch and along bumpers edge. Remove 4 screws from the rear face of the bumper beam. Remove three bolts from each
side of the bumper beam. Starting at bumper tips, carefully peel away the bumper and the beam from the vehicle unclipping any
wiring attached. Unscrew the bumper beam from the bumper disconnecting the wiring loom attached, hand the beam back to the
customer.
4. Loosely attach the Sidearms (C & D) onto the chassis mounting points using fixings (E).
5. Standard i20: Cut the central bumper mounting bracket off crash beam (composite material). Place adhesive foam onto either crash
beam or towbar mainframe. Pull down lower bumper edge, loosely attach Crossbar (A) to side arms (C & D) using fixings (F) pushing
the centre up to beam as far as possible.
6. i20 Active: Loosely attach Crossbar (A) and Bumper Support Angle (J) to Sidearms (C & D) using fixings (F). Attach Bumper
Support Plates (K) to Angles (J) using fixings (L). When the bumper is re-fitted it is supported here with existing fixings.
7. Tighten all fixings, cut bumper as per drawing and refit. Note: larger cut required for detachable option due to retractable electrical
plate. To re-fit L/H side plastic panel a small cut across the rib may be required to allow the panel to fold inside the sidearm (as per
drawing below).
8. Attach neck option.
Recommended torque settings: Grade 8.8 bolts: M8 - 24Nm, M10 - 52 Nm, M12 - 80 Nm, M14 - 130 Nm, M16 - 200 Nm Grade
10.9: M12 – 120Nm, M10 – 70Nm M8- 35Nm
Fitting
Instruction
s
µW0001HY63U-FIT$011504210000ÆÄ
W0001HY63U-FIT$011504210000
HYUNDAI TOWBAR for:
i20
i20 Active
HY63U