LVI Athena A Notice De Montage Et D'utilisation page 4

EnGLISh
Congratulations on your purchase
of a new towelwarmer from LVI
Towel dryer with power supply cable and plug, fitted with 2-pole switch for
connection and disconnection. The switch has a red lamp that lights up when
the towel dryer is switched on. Adaptable for fixed/concealed connection to the
mains. Delivered with wall brackets and screws.
rated voltage: 230 V 50 Hz . For Australia: 230V-240V
Enclosure class: IP 44
Double insulation
InstallatIon
PosItIonIng
The frame of the towel dryer may be inserted in zone 1, but it must be placed
so that the switch is positioned in zone 2 or 3, see figures 1-4. Since the towel
dryer is reversible, the switch should be positioned facing away from the bath
or shower. The recommended minimum dimensions to limiting surfaces in the
vicinity are indicated in figures 5-6. It is important to remember that the towel
dryer is there to hang towels on and must not be used to hold on to.
To avoid injuries to small children the towel dryer must be positioned so that
the lowest part is at least 600 mm above the floor. The recommended minimum
dimensions to other limiting surfaces in the vicinity are indicated in figure 3.
Wall-MountIng and connectIon
For the correct installation of radiators it is essential that the fixing of the
radiator is carried out in such a way that it is suitable for intended use and
predictable misuse. A number of elements need to be taken into consideration
including the fixing method used to secure the radiator to the wall, the type and
condition of the wall itself, and any additional potential forces or weights, prior
to finalising installation.
A residual current device of maximum 30 mA is compulsory if the towel dryer is
mounted in bathrooms and shower rooms.
The towel dryer is mounted on a wall with the enclosed screws. The wall brack-
ets can be moved to suit any tile joints etc. They can be loosened and tightened
from the back with the screw in the centre of the wall bracket before the towel
dryer is mounted on the wall, see figure 4.
The cover rings are fitted to conceal the wall screws: the cover rings for the feet
are turned in position with the recess for dismantling facing downwards (5A)
and then snapped into place, see figure 5.
The enclosed cover ring(s) is/are snapped over the connection housing and
where appropriate the wall bracket, see figure 6.
All the feet and wall brackets can be turned round so that the towel dryer can
be reversed.
The towel dryer can then be mounted with the wall bracket and switch either at
the top or bottom, on the left or right side.
toWel dryer WIth PoWer suPPly cable and Plug
The towel dryer's power supply cable with the plug is connected to a wall
socket.
This appliance is equipped with an all-pole switch with a contact separation of
3 mm.
toWel dryer WIth PoWer suPPly cable WIthout Plug
The electrical installation must be done by an authorised electrician.
remove the plug from the power supply cable and connect the 2-wire cable to a
suitable junction box as follows:
Brown wire = phase
Blue wire = neutral
toWel dryer WIth concealed connectIon
The towel dryer can as an alternative be fitted with a concealed electrical con-
nection. The electrical installation must be done by an authorised electrician.
INSTALLATIoN wITH CoNCEALED CoNNECTIoN
1. remove the cover on the connection housing by undoing the screws holding
the cover in place, figure 7.
2. Lift up the connector by means of a pair of pliers,
figure 8.
3. unscrew the wires from the connector.
4. Insert the cable or the equivalent from the wall through the inlet, figure 9.
For connection with wiring tube: replace the fitted membrane inlet with the
enclosed open inlet.
5. Mount the towel dryer on the wall.
6. Connect the incoming wires to the connector.
7. Press the connector on the switch, figure 10.
8. Fit and screw tight the enclosed sealed cover, figure 11.
usIng the toWel dryer
The towel dryer is switched on by pressing the switch. The lamp on the switch
lights up when the towel dryer is switched on. The towel dryer can be left
switched on permanently without problem. The temperature of the towel dryer
can vary.
Product care
only mild detergent should be used to clean and wipe the towel dryer.
MIscellaneous
Failure to follow the installation instructions can lead to overheating and mal-
functioning.
This towel dryer is only intended for the drying of textiles washed in water.
The appliance is not intended for use by young or infirm persons without super-
vision. Young children should be supervised to ensure that they do not play with
the appliance.
LVI cannot accept responsibility for any damage resulting from incorrect use.
If the power supply cable is damaged it must be replaced by the same type sup-
plied by LVI, or LVI's representative.
The power supply cable has LVI part number 4420301 (including chrome cover)
and 4420302 (including white cover). The maximum surface temperature that
can be achieved on a free surface is 60ºC.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
WARANTy
The warranty is valid for 10 years except for electrical components which
is valid for 2 years. In the event of any problems or repairs, please contact
your supplier.
- 4 -