Bosch GSS 18V-10 Professional Notice Originale page 14

14 | English
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Complete dust box (Microfilter system)
(2) Rear clamping bracket
(3) Sanding plate
(4) Sanding-sheet clamps (x 2)
(5) Square base plate
A)
(6) Sanding sheet
(7) Front clamping bracket
(8) On/off switch
(9) Button for charge indicator
(10) Battery charge indicator
A)
(11) Battery
(12) Battery release button
(13) Handle (insulated gripping surface)
(14) Screws for base plate (x 4)
(15) Extraction outlet
(16) Filter element (Microfilter system)
(17) Dust extraction adapter
(18) Dust extraction hose
A)
(19) Punch
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Orbital sander
Article number
Rated voltage
No-load speed
No-load orbital stroke rate
Sanding sheet surface
Orbit diameter
Dimensions
Weight according to EPTA
Procedure 01:2014
Permitted ambient temperature
– during charging
B)
– during operation and
during storage
Recommended batteries
Recommended chargers
A) Depends on battery in use
1 609 92A 4AB | (18.05.2018)
A)
A)
A)
A)
A)
GSS 18V-10
3 601 JD0 2..
V=
rpm 11,000
rpm 22,000
2
cm 114.7
mm
mm 199.5 x 113 x 141
kg 1.4/1.7
°C 0 to +45
°C -20 to +50
GBA 18 V..
GBA 18 V... W
AL 18..
GAL 3680
GAL 18V... W
B) Limited performance at temperatures <0 °C
Noise/vibration information
Noise emission values determined according to
EN 62841-2-4.
Typically, the A-weighted sound pressure level of the power
tool is 76 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed 80 dB(A).
Wear hearing protection
Total vibration values a
determined according to EN 62841-2-4:
2
a = 7.5 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure detailed in EN 62841
and may be used to compare power tools. They may also be
used for a preliminary estimation of vibration and noise
emissions.
The given vibration level and noise emission value represent
the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
18
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
1.6
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
A)
Battery Charging
Use only the chargers listed on the accessories page.
u
Only these chargers are matched to the lithium-ion bat-
tery of your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
(triax vector sum) and uncertainty K
h
2
,
Bosch Power Tools