Conformity And Approval; Charging The Batteries - Monacor JTS KA-10/1PACK Mode D'emploi

For wireless transmission, 16 channels are
available in the frequency range 863 – 865 MHz.
Up to three of these channels can be used at the
same time without mutual interference. The trans-
mission range depends on local conditions and
may reach 60 m as a maximum.

3.1 Conformity and approval

Herewith, MONACOR INTERNATIONAL declare
that the transmitter of the transmission system
KA-10/1PACK is in accordance with the basic
requirements and the other relevant regulations of
the directive 1999 / 5 / EC. The declaration of con-
formity is available on request from MONACOR
INTERNATIONAL.
The transmission system is licence-free and gen-
erally approved for operation in EU and EFTA
countries.

4 Charging the Batteries

The transmitter and the receiver are supplied with
power via a built-in rechargeable lithium-ion bat-
tery: Prior to initial operation, fully recharge the bat-
teries.
1) Connect the power supply unit provided to the
jack "12 V 500 mA" (12) of the charger, then
connect the power supply unit to a mains socket
(230 V~ / 50 Hz). The charging LEDs (14) keep
flashing as long as the charging slots (13) are
empty.
2) Insert the transmitter and the receiver into the
charging slots according to fig. 4. After a few
seconds, the charging LEDs light up. If they fail
to light up, push the units deeper into the slots.
3) When the battery of a unit has been fully
recharged, the corresponding charging LED is
extinguished. The unit can be removed from the
slot.
4) After the batteries have been charged, discon-
nect the power supply unit of the charger from
the mains socket.
Notes
– If a charging LED keeps flashing during the
charging process, the charger performs a self-
test to protect the batteries.
– To ensure a long battery life, do not store the
units with discharged batteries. If the units are
not used for a longer period, recharge the bat-
teries every three months.
– To replace the battery, the unit must be opened.
Therefore, a defective battery must always be
replaced by skilled personnel. A suitable
replacement battery is available: TG-3.7VB
(order no. 28.2460).
Never put defective batteries in the house-
hold waste; always take them to a special
waste disposal, e. g. collection container at
your retailer.
5 Fastening and Connecting the Units
For a better distinction between the units, the hous-
ing of the transmitter is black and marked with a
large T at the front; the housing of the receiver is
grey and marked with a large R.
1) The transmitter and the receiver are both pro-
vided with a clip (5). This clip can be used to fas-
ten the units on your clothes, e. g. belt or trouser
pocket.
Alternatively, use the supplied shoe mount
adapter (11) to screw one of the units onto a
camera support with 6.3 mm thread (
adapter can also be used to mount the receiver
on the shoe for the video light / flash unit of the
camera. To hold the shoe mount adapter in
place, put it under the clip of the transmitter or
the receiver (fig. 3).
2) The transmitter is equipped with a built-in micro-
phone (9) to pick up the sound. It is also possi-
ble to connect the supplied tie clip microphone
to the jack MIC / LINE (1); in this case, the built-
in microphone is switched off. If required, put
the supplied windshield / pop shield on the tie
clip microphone. To attach the microphone, e. g.
to your tie, fasten the supplied clip to the micro-
phone cable.
If the KA-10 /1PACK is used for wireless
transmission of line audio signals, connect the
audio source (CD / MP3 player, radio, mixer etc.)
to the jack MIC / LINE.
3) Connect the jack AF OUT (1) of the receiver to
the audio input of the camera or the following
unit (amplifier, mixer etc.). A connection cable
with two 3.5 mm plugs and an adapter cable
(3.5 mm plugs to XLR plugs) is supplied with the
system.
1
⁄ "). The
4
9