Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
BEFORE STARTING ENGINE
WARNING:
ing and after use. Do not touch the muffler or
allow combustible material such as dry
grass or fuel to do so.
WARNING:
handling information in the safety rules sec-
tion of this manual before you begin. If you do
not understand the fuel handling information
do not attempt to fuel your unit. Seek help
from someone that does understand the in-
formation or call the customer assistance
help line at 1-800-554-6723.
FUELING ENGINE
WARNING:
ly when refueling.
HELPFUL TIP
To obtain the correct oil mix
ratio, pour 3.2 ounces of
2- cycle synthetic oil into
one gallon of fresh gas.
IMPORTANT:
This equipment is designed
to operate on unleaded gasoline with a minim-
um 87 octane (R+M/2 method), with ethanol
blended up to 10% maximum by volume
(E-10). Before operation, gasoline must be
mixed with a good quality synthetic 2-cycle
air-cooled engine oil designed to be mixed at a
ratio of 40:1. Poulan/WEED EATER brand
synthetic oil is recommended. Mix gasoline
and oil at a ratio of 40:1. A 40:1 ratio is obtained
by mixing 3.2 fluid ounces of oil with 1 gallon of
unleaded gasoline. DO NOT USE automotive
oil or marine oil. These oils will cause engine
damage. When mixing fuel, follow instructions
printed on container. Once oil is added to gas-
oline, shake container momentarily to assure
that the fuel is thoroughly mixed. Always read
and follow the safety rules relating to fuel before
fueling your unit. Purchase fuel in quantities
that can be used within 30 days to assure fuel
freshness.
CAUTION:
Never use straight gasoline in
your unit. This will cause permanent engine
damage and void the limited warranty. Do not
use alternate fuels such as ethanol blends
above 10% by volume (E-15, E-85) or any
methanol blended fuel. Use of these fuels can
cause major engine performance and durability
problems.
BAR AND CHAIN LUBRICATION
The bar and chain require continuous lubri-
cation. Lubrication is provided by the auto-
matic oiler system when the oil tank is kept
filled. Lack of oil will quickly ruin the bar and
chain. Too little oil will cause overheating
shown by smoke coming from the chain and/
or discoloration of the bar.
In freezing weather oil will thicken, making it
necessary to thin bar and chain oil with a
small amount (5 to 10%) of #1 Diesel Fuel or
kerosene. Bar and chain oil must be free
flowing for the oil system to pump enough oil
for adequate lubrication.
Muffler is very hot dur-
Be sure to read the fuel
Remove fuel cap slow-
Genuine Poulan or Poulan PRO bar and
chain oil is recommended to protect your unit
against excessive wear from heat and fric-
tion. Poulan or Poulan PRO oil resists high
temperature thinning.
If Poulan or Poulan PRO bar and chain oil is
not available, use a good grade SAE 30 oil.
S Never use waste oil for bar and chain lubri-
cation.
S Always stop the engine before removing
the oil cap.
CHAIN BRAKE
Ensure chain brake is disengaged by pulling
the front hand guard back toward the front han-
dle as far as possible. The chain brake must be
disengaged before cutting with the saw.
WARNING:
move when the engine runs at idle speed. If
the chain moves at idle speed refer to CAR-
BURETOR
ADJUSTMENT
manual. Avoid contact with the muffler. A hot
muffler can cause serious burns.
To stop the engine move the ON/STOP
switch to the STOP position.
To start the engine hold the saw firmly on the
ground as illustrated. Make sure the chain is
free to turn without contacting any object.
Use only 15" - 18" (40 - 45 cm) of
rope per pull.
Hold saw firmly while pulling starter rope.
Starter Rope Handle
Right Foot Through Rear Handle
WARNING:
or drop- start the chain saw. Doing so will put
the operator at risk of serious injury due to
loss of control of the chain saw.
IMPORTANT POINTS TO REMEMBER
When pulling the starter rope, do not use the
full extent of the rope as this can cause the
rope to break. Do not let starter rope snap
back. Hold the handle and let the rope re-
wind slowly.
For cold weather starting, start the unit at
FULL CHOKE; allow the engine to warm up
before squeezing the throttle trigger.
NOTE:
Do not attempt to cut material with
the choke/fast idle lever in the FULL CHOKE
position.
If your engine still does not
start after following these
instructions, please call
1- 800- 554- 6723.
10
The chain must not
within
Left Hand
on Front
Handle
Do not attempt to throw
HELPFUL TIP
this
Publicité
Table des Matières
