Product Familiarisation - Silverline 128966 Traduction Des Instructions D'origine

128966
b) Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators. There is an increased risk
of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering
a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal
injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-
position before connecting to power source and/or battery pack,
picking up or carrying the tool. Carrying power tools with your finger
on the switch or energising power tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench before turning the power tool
on. A wrench or a key left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your
hair, clothing and gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to
operate the power tool. Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that may
affect the power tool's operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working
conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous
situation.
180mm Sander Polisher
5) Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of
the power tool is maintained.
Wallpaper Steam Stripper Safety
• Do not handle the product with wet hands. Do not use the wallpaper
stripper in wet environments or on wet floors
• Fill the water tank, and tighten safety cap securely before connecting to
power supply
• Do not tilt the product by more than 45˚. Tilting the product too far may
allow boiling water to be ejected
• Never direct steam towards people, animals, or electrical equipment
• Always disconnect power supply before filling or cleaning, and after use
• Allow the product to cool fully before opening tank cap
• Do not use any form of rust or calcium remover in this product
• Do not overfill the water tank
• Disconnect from power on completion of the task
• This appliance shall not be left unattended while it is connected to the
mains power supply
• Do not remove the tank cap during use, or whilst the machine is
connected to the mains
• The appliance is not to be used if it has been dropped, or if there are
visual signs of damage
• Keep the appliance out of reach of children whilst it is energised or
cooling down

Product Familiarisation

1 Water Tank
2 Safety Valve
3 Tank Cap
4 Handle
5 Steam Pad
6 Hose
Intended Use
Mains-powered steam cleaner capable of removing all types of wallpaper
without the need for harmful chemicals.
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all
its features and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool
Before Use
WARNING: Ensure the tool is disconnected from the power supply
before attaching or changing any accessories, or making any adjustments.
Assembly
• Attach the Hose (6) to the Water Tank (1) by gripping the Hose end and
installing it to the Safety Valve (2)
• Grip the Hose firmly and fasten it to the Steam Pad (5)
NOTE: Ensure that the hose is securely attached to both the tank and steam
pad; otherwise it may lead to boiling water leaking onto the work area.
www.silverlinetools.com
5