Accessories - Silverline 128966 Traduction Des Instructions D'origine

Masquer les pouces Voir aussi pour 128966:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 8
GB
Filling
• Ensure that the product is unplugged and cool, and that all steam has
been released through the Steam Pad (5)
• Place the product on a level surface then unscrew the Tank Cap (3)
• Fill the Water Tank (1) to the required level, maximum capacity 4.5L
• Securely fasten the Tank Cap (3) to the Water Tank
NOTE: Do not exceed the maximum capacity of the water tank.
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and
hearing protection, as well as suitable gloves, when working with this tool.
WARNING: Caution when stripping wallpaper from delicate surfaces. The
high temperature steam may cause damage to the base surface.
IMPORTANT: When in use, ALWAYS keep the water level in between the
min and max line. DO NOT overfill; DO NOT let the device run dry. If the
device runs dry, it may cause damage. Monitor the water level consistently
during use.
Switching on
• With the Water Tank (1) full, and the Tank Cap (3) secure, the power
supply can be plugged in to the mains and turned on
• After 15 minutes the wallpaper stripper will be ready for use
NOTE: Steam will be ejected from the Steam Pad (5) once the fluid has
reached normal operating temperature.
Wallpaper stripper tips
WARNING: When the Water Tank (1) is full, the wallpaper stripper has an
approximate operating time of 70 minutes. Do not allow the Water Tank to
run dry, or run the machine for longer than 70 minutes.
• Use a wallpaper perforator (not included) on the wall prior to steam
stripper use, to help the steam to penetrate the surface
• When the wallpaper stripper has reached normal operating
temperature, hold the Steam Pad (5) against the wall. Do not hold the
Steam Pad against the wallpaper for longer than 10 seconds
• Use a suitable scraper to remove the wallpaper
• When the wallpaper stripper is running low on water, disconnect from
the mains and allow to cool before opening the Tank Cap (3) and
refilling

Accessories

• A range of accessories and consumables, including Wallpaper
Perforator (245130), Heavy Duty Scraper (CB35) and Wallpaper Guide
Knife (457066), is available from your Silverline stockist. Spare parts
can be obtained from toolsparesonline.com
Maintenance
WARNING: Always remove the plug from the mains power supply
before carrying out any maintenance/cleaning.
Cleaning
• Keep your machine clean at all times. Dirt and dust will cause internal
parts to wear quickly, shortening the machine's service life.
• Clean the body of your machine with a soft brush, or dry cloth.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or
wear. Repairs should be carried out by an authorised Silverline service
centre. This advice also applies to extension cords used with this tool
6
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts
to wear quickly, and shorten the machine's service life. Clean the body
of your machine with a soft brush, or dry cloth. If available, use clean,
dry, compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do
not use alcohol, petrol or strong cleaning agents
• Never use caustic agents to clean plastic parts
Storage
• Store this tool carefully in a secure, dry place out of the reach of
children
Disposal
Always adhere to national regulations when disposing of power tools that
are no longer functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic
equipment, with household waste
• Contact your local waste disposal authority for information on the
correct way to dispose of tools

Publicité

Table des Matières
loading

Table des Matières