LGB 55024 Instructions De Service page 3

GB
USA
55024
MTS Switch Decoder, Single
Channel
Use this decoder to control one EPL
switch, one EPL signal or one EPL
uncoupler with the LGB Multi-Train
System. The decoder connects
directly to the EPL drive and to the
tracks. It is very simple to connect
and to operate.
Specifications:
- single terminal for triggering
impulse for one EPL drive
- weather-resistant construction
(resin-dipped circuit board)
- max. output current: 1 amp
- impulse duration: 0.8 sec.
- overload protection (short circuit),
automatic Reset
- up to 2047 switch addresses (with
LGB MTS: 128)
- compatible with NMRA DCC
Installation
Connect the two terminals under-
neath the switch decoder to the
tracks (Fig. 1). Place the two pins on
the decoder into the orange and
white terminals on the EPL drive and
tighten the screws.
Programming the switch decoder
address
The switch decoder is protected
against accidental reprogramming.
This allows programming loco
addresses on your layout without
having to remove switch decoders
from the tracks. Programming the
switch decoder is possible only after
CV2 has been programmed to func-
tion value "77." Then you can pro-
gram the switch decoder address in
CV1. (Before each programming of a
CV, the programming protection has
6
to be deactivated by setting CV2 to
"77.")
Hint: With the LGB Multi-Train
System, only addresses 1-128 can
be used.
The LGB 55024 single-channel switch decoder features the following CVs:
Register Function
CV1 Switch decoder address
CV2 Programming protection (input "77" to allow one-time
programming of a single CV)
CV3 Switch setting direction ("0": normal; "1": inverse)
CV7 Input "55" to reset loco address (CV1 and CV9) to "1"
During read-out: software version
CV8 Manufacturer code, read only
CV9 Switch decoder address Byte 2 (address x 256)
For addresses above 255, byte 1 is programmed in CV1
and byte 2 in CV9: Address = CV9 x 256 + CV 1.
(Not for LGB MTS)
No other functions can be pro-
grammed. For advanced applica-
tions, we recommend the LGB 55025
MTS Switch Decoder.
AUTHORIZED SERVICE
Improper service will void your war-
ranty. For quality service, contact
your authorized retailer or one of the
following LGB factory service sta-
tions:
Ernst Paul Lehmann Patentwerk
Reparatur-Abteilung
Saganer Strasse 1-5
D-90475 Nürnberg
GERMANY
Telephone: (0911) 83707 0
Fax: (0911) 83707 70
LGB of America
Repair Department
6444 Nancy Ridge Drive
San Diego, CA 92121
USA
Telephone: (858) 795-0700
Fax: (858) 795-0780
You are responsible for any shipping
costs, insurance and customs fees.
Hint: Information on LGB products
and LGB representatives around the
world is available online
www.lgb.com
Available Factory
values
(1-255)
(0-1)
(0-7)
CAUTION! This product is not for
children under 8 years of age. Save
the supplied packaging and instruc-
tions.
Products, specifications and avail-
ability dates are subject to change
without notice. Some products are
not available in all markets and at all
retailers. Some products shown are
pre-production prototypes. LGB,
LGB of America, LEHMANN and the
LGB TOYTRAIN logotype are regis-
tered trademarks of Ernst Paul
Lehmann Patentwerk, Germany.
Other trademarks are the property of
their owners. © 2006 Ernst Paul
Lehmann Patentwerk.
at
pre-set
[1]
[0]
[123]
[0]
7