Technical Data; Delivery Scope - Bosch GTA 3800 Professional Notice Originale

OBJ_BUCH-1199-002.book Page 16 Tuesday, January 17, 2017 12:25 PM
16 | English
15 Locking pin
16 Button for releasing lever 17
17 Lever for locking the attachment set
18 Movable nut
19 Fastening kit, power tool
20 Fastening kit for transport wheels*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Saw stand
Article number
Length of saw stand without
table extension
Length of saw stand with
table extension
Height of saw stand
Max. carrying capacity
(power tool + workpiece)
without table extension
– Attachment set
Max. carrying capacity
(power tool + workpiece)
with table extension
– Attachment set
– Per table extension
Weight according to
EPTA-Procedure 01:2014
Assembly

Delivery Scope

Please also observe the representation of
the delivery scope at the beginning of the
operating instructions.
Before assembling the saw stand, check if all parts listed be-
low are provided:
No. Designation
Saw stand GTA 3800
4 Attachment set
1 Workpiece support
7 Roller stand
14 Socket spanner/hex key/cross-head
screwdriver 14
19 Power tool fastening kit consisting of:
– Hexagon bolt (M8 x 45)
– Washer
Additionally required tools (not in delivery scope):
– Open-end spanner (10 mm)
1 609 92A 2M9 | (17.1.17)
Assembling the Saw Stand
Carefully remove all parts included in the delivery from their
packaging.
Remove all packaging material.
Setting Up the Saw Stand (see figures A1 – A2)
Lay the saw stand upside down on the floor (legs facing
upward).
Push the locking pin 15 in and tilt the leg upward until the
locking pin can be heard to engage.
Repeat this workstep with the other three legs.
Turn around the saw stand to the working position.
GTA 3800
Ensure that the saw stand is stable and that all locking pins
3 601 M24 000
have engaged.
The saw stand is easily aligned with the height-adjustable
mm 1578
leg 9.
Screw the leg in or out until the saw stand is aligned level and
mm 3877
all four legs face against the floor.
mm 824
Mounting the Roller Stand (see figure B1)
Unscrew the cross-head screw of the roller stand 7 with the
cross-head screwdriver 14 provided.
If required, counter-hold the lock nut on the other side of the
kg 250
roller stand using a spanner (size 10 mm).
Disassemble the roller stand 7.
There are different possibilities to arrange the individual
kg 150
rollers to the workpiece support with the internally-threaded
kg 50
rod (see figure).
Arrange the individual parts as required and slide the inter-
kg 22.4
nally-threaded rod through the rollers and the workpiece sup-
port 1.
Screw all parts together again.
Mounting the Workpiece Support (see figure B2)
Loosen the locking knobs 3 and pull the table extensions 2 via
both sides of the saw stand lightly outward.
Slide the workpiece supports 1 from the left and right each
into the upper groove of the saw stand or the table extension.
The length stops 8 must face outward.
Tighten the locking knob 6 to lock the workpiece support.
Preparing the Saw Stand
Preparing the Attachment Sets (see figures C1 – C4)
Quantity
To release the attachment sets 4, press buttons 16 each and
1
open the levers 17.
2
Measure the distance x between the mounting holes and your
2
power tool.
2
Position the attachment sets 4 centred on the saw stand and
at the matching clearance x to each other.
1
Lock the levers 17 again. The attachment sets are now firmly
positioned on the saw stand.
4
Fastening the Power Tool to the Attachment Sets
4
(see figure D)
Position the power tool in the transport position.
Notes on the transport position are given in the operating
instructions of the respective power tool.
Bosch Power Tools