Maintenance And Service - Bosch GTA 3800 Professional Notice Originale

OBJ_BUCH-1199-002.book Page 17 Tuesday, January 17, 2017 12:25 PM
Position the movable nuts 18 in the attachment sets so that
they match the mounting holes of the power tool.
Screw the attachment set and the power tool with the hexa-
gon bolts and the washers from the fastening kit 19 using the
provided socket spanner 14.
Operation
Working Advice
Do not overload the saw stand. Always observe the maximum
carrying capacity of the saw stand and the two table exten-
sions.
Always hold the workpiece firmly, especially the longer and
more heavy section. After cutting through the workpiece, the
centre of gravity may become dislocated in such an unfavour-
able manner that the saw stand tips over.
Preparing the Workpiece Support
Long workpieces must be underlaid or supported at their free
end.
Adjusting the Height of the Workpiece Support
(see figure E)
Place your workpiece onto the saw table of the power tool.
Loosen locking knob 5 and adjust the height of the roller stand
7 so that the workpiece rests level.
Retighten the locking knobs again.
Sawing Workpieces of the Same Length (see figure F)
The material stop 8 can be used for easily sawing workpieces
to the same length.
Pull the length stop 8 upward until it engages.
Position the workpiece support 1 at the desired clearance to
the saw blade of the power tool.
To slide in the length stop 8, tilt it inward and push it all the
way down.
Extending the Saw Stand (see figure G)
The saw stand can be extended on both sides.
To stabilise the saw stand when working long and heavy work-
pieces, the table extension 2 can be supported with a support
leg 13 (see "Support Leg for Supporting the Table Extension",
page 17).
Place your long workpiece onto the saw table of the power
tool.
Release the respective locking knob 3 as required, and pull
the table extension 2 out to the desired position.
Retighten the locking knobs again.
Fitting the Accessories
Support Leg for Supporting the Table Extension
(see figure H)
To stabilise the saw stand when working long and heavy work-
pieces, the table extension 2 can be supported with a support
leg 13.
Bosch Power Tools
The support leg 13 can be fastened either to the left or right of
the saw stand.
Loosen locking knob 3 and pull the table extension 2 to be
supported somewhat outward.
Slide the screw head of the support leg 13 into the bottom
groove of the table extension 2.
Tighten the support leg 13.
Screw the height adjustment of the support leg 13 in or out
until the saw table is aligned level again.
Transport Wheels and Stop for Swift Changing of the
Location (see figures I1 – I2)
The transport wheels 12 enable the saw stand to be trans-
ported to a different location, without having to remove the
mounted stationary saw.
The transport wheels 12 can be fastened either to the left or
right of the saw stand.
For assembly, use the fastening kit 20.
Lay the saw stand upside down on the floor (the folded-in legs
facing upward).
Screw the transport wheels at the desired location to the saw
table with the four screws and nuts.
Use the provided hex key 14 for this.
Turn around the saw stand to the working position.
Loosen the locking knob 3 on the side of the saw stand on
which the transport wheels are fastened and pull the table
extension 2 lightly outward.
Insert the transport stop 11 into the upper groove of the saw
stand and slide the transport stop to the attachment set 4.
Firmly tighten the hexagon bolt in the stop with the provided
socket spanner 14.
When transporting, the attachment set with the mounted
power tool can no longer slip off.
Transport (see figure J)
The saw stand must be folded together for transport.
In case a support leg 13 is mounted, remove it.
Slide the table extensions 2 completely inward.
Tilt all legs inward (press locking pin 15 inward; tilt each leg
inward until the locking pin can be heard to engage again).
Grasp the recessed handle and lift up the saw stand.

Maintenance and Service

Accessories
Attachment set . . . . . . . . . . . . . . . . . . . . . . . . 2 610 948 662
Workpiece support . . . . . . . . . . . . . . . . . . . . . 1 609 B01 851
Height-adjustable support leg . . . . . . . . . . . . 1 609 B01 855
Transport wheel set
(wheels, stop, fastening kit) . . . . . . . . . . . . . 1 609 B01 854
English | 17
1 609 92A 2M9 | (17.1.17)