Table des Matières
Publicité
12
| English
TECHNICAL DATA
Article Number
Model
Voltage
Rated Power Input
No Load Speed
Cutting width
Cutting height
Collector Capacity
Weight
Sound emission values determined according to
EN 60335-1, EN 60335-2-77
Typically the A-weighted noise levels of the product are:
Sound pressure level
Guaranteed sound
power level
Uncertainty K
Vibration total values a
and uncertainty K determined according to EN
60335-1, EN 60335-2-77
Vibration level max:
a
h ,HD
K
IDENTIFICATION
1. Switch box
2. Switch lever
3. Extension cord restrain hook
4. Cable clip
5. Grass collector
6. Collector flap
7. Upper handle
8. Lower handle
9. Motor housing
10. Rear wheels
11. Front wheels
12. Grass indicator flap
ASSEMBLY
Put the cable hook on the upper handle, close to the
f
starting point (B).
Connect upper and lower handles with supplied
f
screws and knobs (C).
Insert the handles into the mower body and tighten
f
the fixed screws (D).
Clip the cable clip on the handle. Clip the cord into
f
the cable clip (E).
GRASS COLLECTOR ASSEMBLY AND FITTING
The grass collector (5) prevents grass clippings
being thrown across your lawn as you mow.
42 412
ELM 32/1000 EASY
V
220-240
Hz
50
W
1.000
min
3.400
-1
mm
320
mm
20,40,60
L
25
Kg
6,2
dB(A)
82,5
dB(A)
96
dB
2,5
(triax vector sum)
h
m/s
1,742
2
m/s
1,5
2
1. Insert the grass collector handle into the holes
on the top of grass collector until it clicks in (F).
2. Align the upper and lower grass collector sec-
tions and join. Ensure the clips are located cor-
rectly and securely (G).
3. Fix the supporting rod by inserting the edges
into the holes (f1) and after push the sides into
the slots (f2) on both sides of the bag (F).
4. Clip the protective plastic straps onto the sup-
port rod of the grass collector (H).
5. Lift the collector flap (6) with one hand. With
the other hand hold the grass collector by the
handle and hook it in from above (J).
OPERATION
WARNING! Before connecting to the mains
supply, always check the switch is in the off
position!
EXTENSION CORD RESTRAINT (S)
We recommend using your mower as outlined in
this section to achieve optimum results and to re-
duce the risk of cutting the mains cable. Place the
bulk of the mains cable on the lawn, close to the
starting point. Feed the cable through the cable
restraint (3).
ADJUSTING THE CUTTING HEIGHT (K, L)
This electric lawn mower is equipped with a 3-po-
sition height adjustment system. To obtain the
desired cutting height, the front and rear axles
are repositioned on the underside of the mower
housing.
WARNING! Disconnect the mower from the
power supply and ensure the blade has
stopped coasting before adjusting the
height.
1. To adjust the front wheel cutting height posi-
tion (K)
a. Turn the mower upside down.
b. Pull the wheel axle towards the front of the
mower.
c. Locate the wheel axle into the desired cut-
ting height adjustment position.
Note: Make sure that both front right and left
wheel are located in the same cutting height ad-
justment position.
2. To adjust the rear wheel cutting height position
(L)
a. Turn the mower on its side.
b. Pull the rear wheel axle towards the mow-
er's collector flap.
c. Locate the wheel axle into the desire cutting
height adjustment position.
STARTING THE MOTOR
1. Plug the machine into the electric supply, ensur-
ing it meets the recommended requirements.
Electrical power should be supplied via a residual
current device (RCD) with a tripping current of
not more than 30 mA.
2. Before starting the lawn mower, hold the handle
ELM 32/1000 EASY
Publicité
Table des Matières
