Specific Safety Rules - Makita TW0350 Manuel D'instruction

Masquer les pouces Voir aussi pour TW0350:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

12. Remove adjusting keys or wrenches before turn-
ing the tool on. A wrench or a key that is left
attached to a rotating part of the tool may result in
personal injury.
13. Do not overreach. Keep proper footing and bal-
ance at all times. Proper footing and balance
enables better control of the tool in unexpected situ-
ations.
14. Use safety equipment. Always wear eye protec-
tion. Dust mask, non-skid safety shoes, hard hat, or
hearing protection must be used for appropriate con-
ditions. Ordinary eye or sun glasses are NOT eye
protection.
Tool Use and Care
15. Use clamps or other practical way to secure and
support the workpiece to a stable platform. Hold-
ing the work by hand or against your body is unsta-
ble and may lead to loss of control.
16. Do not force tool. Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it is designed.
17. Do not use tool if switch does not turn it on or
off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
18. Disconnect the plug from the power source
before
making
accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool
accidentally.
19. Store idle tools out of reach of children and
other untrained persons. Tools are dangerous in
the hands of untrained users.
Ampere Rating
More Than
0
6
10
12

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with
product (gained from repeated use)
replace
strict
wrench safety rules. If you use this tool
unsafely or incorrectly, you can suffer
serious personal injury.
any
adjustments,
Table 1: Minimum gage for cord
Not More Than
6
10
12
16
adherence
to
20. Maintain tools with care. Keep cutting tools
sharp and clean. Properly maintained tools with
sharp cutting edges are less likely to bind and are
easier to control.
21. Check for misalignment or binding of moving
parts, breakage of parts, and any other condition
that may affect the tools operation. If damaged,
have the tool serviced before using. Many acci-
dents are caused by poorly maintained tools.
22. Use only accessories that are recommended by
the manufacturer for your model. Accessories
that may be suitable for one tool, may become haz-
ardous when used on another tool.
SERVICE
23. Tool service must be performed only by quali-
fied repair personnel. Service or maintenance per-
formed by unqualified personnel could result in a
risk of injury.
24. When servicing a tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unau-
thorized parts or failure to follow Maintenance
instructions may create a risk of electric shock or
injury.
USE PROPER EXTENSION CORD: Make sure your
extension cord is in good condition. When using an
changing
extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating. Table 1 shows the correct size to
use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gage. The smaller
the gage number, the heavier the cord.
Volts
120 V
25 ft.
18
18
16
14
1.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
USB003-2
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal parts
of the tool "live" and shock the operator.
2.
Wear ear protectors.
impact
3.
Check the socket carefully for wear, cracks or
damage before installation.
4.
Hold the tool firmly.
3
Total length of cord in feet
50 ft.
100 ft.
AWG
16
16
16
14
16
14
12
Not Recommended
150 ft.
14
12
12

Publicité

Table des Matières
loading

Table des Matières