Milwaukee M18 FUEL 2783-20 Manuel De L'utilisateur page 6

Only use accessories with Maxi-
WARNING
mum Safe Operating Speed rated
at least equal to the maximum speed marked on
the power tool. This speed is based on the
strength of the wheel, allowing for a reasonable
measure of safety. It is not meant to imply a best
or most efficient operating speed. Do not exceed
the Maximum Safe Operating Speed.
Installing/Removing Grinding Wheels
Make sure the wheel does not extend beyond the
bottom of the guard. Threaded hub grinding wheels
may require a deeper guard (see "Accessories").
1. Remove the battery pack. WARNING! Always
remove battery pack before changing or removing
accessories.
2. Properly position the guard.
3. Wipe the flange, FIXTEC nut and spindle to re-
move dust and debris. Inspect the parts for dam-
age. Replace if needed. Use only MILWAUKEE
mounting hardware designed for your tool.
4. Place the flange on spindle, as shown.
5. Place the selected wheel on the spindle and align
it with the flange.
6. Press in the spindle lock button. With the tightening
tab up, thread the FIXTEC nut clockwise onto the
spindle. Use the tightening tab on the FIXTEC nut
to grasp the nut and tighten securely. Press down
the tightening tab.
7. To remove wheel, remove the battery pack and
reverse the procedure.
Sanding Disc Selection
Use sanding discs and accessories that are:
• correct size as written on tool's nameplate.
• rated at or above the RPM listed on the tool's name-
plate.
• correct accessory, wheel type and grit for the job.
Select the correct type of sanding disc for your job.
Generally, use 24 or 36 grit for heavy stock removal;
50, 60, or 80 grit for medium stock removal and 120
grit for finishing. Always begin with a coarse grit, us-
ing successively finer grits to obtain the desired finish.
•Aluminum Oxide: For fast cutting, general purpose
discs for most metal jobs. Best for cold-rolled steel,
stainless steel or metals requiring tough, fast cutting,
long lasting abrasives.
•Aluminum Zirconia Bi-Cut: Unique grit pattern is
arranged in clusters for faster stock removal and
cleaning. Ideal for removing paint from cars, boats,
etc. without clogging.
Tightening tab
FIXTEC nut
Wheel
Flange
Spindle
•Ceramic: Lasts up to 3 times longer than Aluminum
Oxide Discs. For general metal working. Ideal for
tough jobs.
Installing Backing Pad and Sanding Discs
1. Remove the battery pack. WARNING! Always
remove battery pack before changing or removing
accessories.
2. Wipe the accessories, disc nut and spindle to
remove dust and debris. Inspect the parts for dam-
age. Replace if needed. Use only MILWAUKEE
mounting hardware designed for your tool.
3. Slip backing pad onto spindle with flat side away
from gear case.
4. Place sanding disc on backing pad and secure
assembly to spindle with disc nut.
5. Press in the spindle lock button while turning flange
nut clockwise. Tighten securely.
6. To remove backing pad and sanding disc, remove
the battery pack and reverse the procedure.
Installing/Removing/Cleaning
the Dust Screen
Using the dust screen will increase the performance
and extend the life of the tool.
1. To attach the dust screen, snap the screen over
the tool's handle.
2. To remove the dust screen, insert a flat screw-
driver into the notch at the top of the dust screen
and pry away from the tool.
3. To clean the dust screen, tap against a hard sur-
face, or blow clean with compressed air.
OPERATION
To reduce the risk of injury, always
WARNING
wear safety goggles or glasses
with side shields. Never grind without proper
safety equipment.
Controlled Start
The controlled start feature reduces the torque reac-
tion "jerk" when the trigger is pulled.
Electric Brake
The electric brake engages when the switch is re-
leased, causing the wheel to stop within seconds.
There may be a delay between the time the switch is
released and when the brake engages. Occasionally
the brake may miss completely. If the brake misses
frequently, have the tool serviced by an authorized
MILWAUKEE service facility. Make sure the tool
comes to a complete stop before laying it down.
6
Disc nut
Sanding
disc
Backing
pad
Spindle