Music Control; Slave Mode; Additional Menu Functions; Specifications - Monacor International IMG STAGELINE XBEAM-410LED Mode D'emploi

6.2.2 Music control

To start the music-controlled show program, select
the setting for the menu item
firm . When the music control is activated, the unit
will respond to sound picked up via the internal
microphone (1) .
When the menu item is set to
unit will automatically go to the "DMX control"
mode .
Note: The music control will be automatically deactivated
when "Slave mode" or "DMX control" is selected .

6.2.3 Slave mode

To operate the unit as a slave (master /slave mode,
refer to chapter 5 .2), select the setting
the menu item
the show program adjusted on the master unit .
When the menu item is set to
the unit will automatically return to its own show
program 1 to 8 adjusted .
Note: A unit set to "Slave" will automatically return to
"Master" when a different operating mode is selected .
Please note: Never set more than one unit to
"Master" in a master /slave chain .

6.3 Additional menu functions

Selecting the pan / tilt speed
For soft and smooth movements of the moving
head during slow motion sequences, select the
setting (low speed) for the menu item
and confirm .
Inverting the pan / tilt direction
To invert the pan direction, select the setting
for the menu item
To invert the tilt direction, select the setting
for the menu item
Inverting the display indication
To turn the display indication by 180° (for up-
side-down installation of the unit), select the set-
ting for the menu item
and con-
again, the
and confirm . The unit will run
and confirm .
and confirm .
and confirm .
Resetting the menu settings
To reset the menu to its factory settings, select
the setting
firm . After resetting the menu settings, the unit
will automatically go to the „DMX control" mode .
Calibration
The menu item
ment of the starting positions for the functions
Pan and Tilt and for the colour wheel and the lens
wheel (refer to the menu structure, chapter 8):
1) Select the setting
menu for the calibration .
2) In the submenu, call up the corresponding menu
for
item ( = Pan, = Tilt, = Colour wheel, = Lens
wheel), correct the value and confirm .
Via
again,
reset to "000": Select
ton ENTER pressed until "000" briefly appears
on the display . Then press the button ENTER
again; otherwise, the display indication will not
disappear automatically .
Note: The calibration values will not be reset when the
menu settings are reset (menu item
Reset
To reset the unit (reset of the motor control), ac-
tivate the function via the menu item
resetting, the unit will return to its previous oper-
ating mode .

7 Specifications

Control protocol: . . . . . . . . . DMX512
Number of DMX channels: . . 7 or 14
Light source: . . . . . . . . . . . . 4 white 10 W LEDs
Beam angle: . . . . . . . . . . . . 3° – 60°
Pan angle: . . . . . . . . . . . . . . 540°
Tilt angle: . . . . . . . . . . . . . . 210°
DMX connections: . . . . . . . . XLR, 3 poles
Pin configuration: . . . . . . . pin 1 = ground
Ambient temperature: . . . . . 0 – 40 °C
Power supply: . . . . . . . . . . . 230 V / 50 Hz
Power consumption: . . . . . . 50 VA
Dimensions: . . . . . . . . . . . . 20 × 29 × 16 cm
Weight: . . . . . . . . . . . . . . . . 4.2 kg
for the menu item
can be used for fine adjust-
and call up the sub-
, all values of the submenu can be
and keep the but-
pin 2 = DMX−
pin 3 = DMX+
and con-
) .
. After
13