Troubleshooting Guide - shark V900TB Manuel D'utilisation

OPERATING INSTRUCTIONS
Cleaning the Filter Ring
WARNING:
Do NOT operate your hand
vacuum without the HEPA type dust cup
filter and the filter ring in place.
NOTE:
For best results, we recommend
replacing the filter ring with a new one
every three (3) months to ensure peak
performance.
Each time you wash your HEPA type dust
cup filter, we recommend you also wash the
filter ring. To do this:
1. To remove the filter ring from the
HEPA type dust cup filter, grasp the
filter ring tab and pull the filter ring's
Velcro closure apart.
(Fig. 13)
Filter Ring Tab
Fig. 13
2. Rinse the filter ring under
lukewarm water until the water
runs clear. (Fig. 14)
Fig. 14
3. Allow a minimum of 24 hours
drying time before replacing the
filter ring onto the HEPA type dust
cup filter.
WARNING:
Do NOT operate your
hand vacuum with a wet filter ring or
HEPA type dust cup filter.
Motor Thermostat
CAUTION
: The suction hole must be
open, free of any obstructions at all
times. Otherwise, the motor will overheat
and could become damaged.
IMPORTANT:
This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
1. Push the On/Off button.
2. Disconnect the plug from the
power source.
3. Check the source of overheating
problem. (i.e. clogged hose,
accessory or HEPA type dust cup
filter)
4. If a clog is found, unclog the
hose, accessory, or clean and
replace the HEPA type dust cup
filter and filters ring.
5. Wait at least 45 minutes before
attempting to reuse the vacuum.
6. After unit has cooled down for
45 minutes, plug in the cleaner
and push the On/Off button. The
vacuum should start again.
7. If the vacuum still does not start,
contact customer service at
1(800) 798-7398.
7
TROUBLE SHOOTING GUIDE
PROBLEM POSSIBLE REASON
1. Power cord not firmly
plugged into outlet.
HAND VACUUM
2. No power in wall outlet.
WILL NOT
3. Hand vacuum needs
OPERATE
servicing.
4. Thermostat has tripped.
1. Dust cup is full.
HAND VACUUM
2. Unit clogged.
WILL NOT PICK-
3. Dust Cup Filter needs
UP OR SUCTION
cleaning or replacing.
POWER IS
4. Hose or accessory is
WEAK
clogged.
AIR DRIVEN 1. Dust cup is full.
TURBO BRUSH 2. Rotating brush or elbow is
DOES NOT clogged.
ROTATE OR 3. Hose is obstructed.
ROTATES 4. HEPA type dust cup filter
SLOWLY is clogged.
1. HEPA type dust cup filter
DUST is full.
ESCAPING 2. HEPA type dust cup filter
FROM HAND is not installed correctly.
VACUUM 3. HEPA type dust cup filter
is damaged.
HAND VACUUM,
HOSE OR 1. Hose is clogged.
BRUSHES WILL 2. Dust cup is full
NOT PICK-UP
POSSIBLE SOLUTION
1. Plug unit in firmly.
2. Check fuse or breaker.
Replace fuse/reset
breaker.
3. Call 1 (800) 798-7398.
4. Turn the unit off and
unplug it from outlet.
Allow the unit to cool off,
then restart.
1. Empty dust cup.
2. Turn unit off and unplug
from wall outlet. Remove
HEPA type dust cup filter
and check for object(s) in
air duct and remove.
3. Clean and replace the
HEPA type dust cup filter.
4. Turn unit off and unplug
from wall outlet. Check for
objects in the hose and/or
accessory.
1. Empty dust cup and clean
HEPA type dust cup filter.
2. Clear obstructions.
3. Clear obstruction.
4. Clean and replace HEPA
type dust cup filter.
1. Empty dust cup (container)
and clean HEPA type dust
cup filter.
2. Replace HEPA type dust
cup filter carefully.
3. Replace HEPA type dust
cup filter with a new one.
1. Remove hose and/or
bushes. Remove
obstruction from hose.
2. Empty dust cup (container)
and clean the HEPA type
dust cup filter.
8