Important; Troubleshooting Guide - shark Transformer Vac EP602RF Guide Du Propriétaire

OPERATING INSTRUCTIONS
Motor Thermostat

IMPORTANT:

This unit is equipped
with a motor protective thermostat. If for
some reason the vacuum cleaner should
overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the On/Off button once.
• Disconnect the plug from the power
source.
• Check the source of overheating
problem. (i.e. clogged hose or filter)
TROUBLE SHOOTING GUIDE
PROBLEM POSSIBLE REASON
1. Power cord not firmly plugged into
outlet.
VACUUM WILL
2. No power in wall outlet.
NOT OPERATE
3. Needs servicing.
4. Thermostat has tripped.
1. Dust cup is full.
VACUUM WILL
2. Unit clogged.
NOT PICK-UP OR
3. HEPA Filter needs cleaning or
SUCTION POWER
replacing.
IS WEAK
4. Debris screen needs cleaning.
5. Filters need cleaning.
1. Dust cup is full.
TURBO BRUSH
2. Rotating brush or elbow is
DOES NOT
obstructed.
ROTATE OR
3. Belt is broken.
ROTATES
4. Hose obstructed.
SLOWLY 5. Debris screen is clogged.
6. Filters need cleaning.
DUST ESCAPING
1. Dust cup is full.
FROM VACUUM
2. Dust cup is not installed correctly.
VACUUM, HOSE
1. Hose clogged.
OR BRUSHES
2. Dust cup is full.
WILL NOT PICK-UP
• If clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for
45 minutes, plug in the cleaner
and push the On/Off button. The
vacuum should start again.
• If the vacuum still does not start,
contact customer service at
1 (800) 798-7398.
POSSIBLE SOLUTION
1. Plug unit in firmly.
2. Check fuse or breaker. Replace
fuse/reset breaker.
3. Call 1 (800) 798-7398.
4. Turn the unit off and unplug from
outlet. Allow unit to cool down,
then restart.
1. Empty and clean dust cup.
2. Turn unit off and unplug from
wall outlet. Remove dust cup
filter and check for object(s) in
air duct and remove.
3. Clean or replace HEPA Filter.
4. Clean debris screen.
5. Clean Filters.
1. Empty dust cup.
2. Clear obstructions.
3. Call 1 (800) 798-7398.
4. Clear obstruction.
5. Clean debris screen.
6. Clean ALL filters.
1. Empty and clean dust cup.
2. Review dust cup instructions.
1. Remove hose and/or brushes.
Remove obstruction from hose
and /or brush.
2. Empty and clean dust cup.
9
ORDERING REPLACEMENT DUST CUP FILTERS
TO ORDER REPLACEMENT HEPA FILTERS
Item # XSH602
for Model EP602RF
Call: 1 (800) 798-7398
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
visit our website: www.sharkvac.com
FOR TECHNICAL SUPPORT
for Model EP602RF
Call: 1 (800) 798-7398
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
Please Note:
The HEPA Filter is washable. It should, however, be replaced every three (3)
to six (6) months to ensure peak performance of your vacuum.
The Pre-Motor, Non-Woven Pre-Filter and Post Motor Filters are washable.
Important:
Make sure that ALL filters have been completely air dried for 24 hours before
re-installing back in the vacuum.
or
10