Specific Safety Instructions; Technical Specifications - Roller Centro S 1 Instructions D'emploi

eng
c) Use battery tools only with specifically designated battery packs. Use
of any other battery packs may create a risk of injury and fire.
d) When battery pack is not in use, keep it away from other metal objects
like paper clips, coins, keys, nails, screws, or other small metal objects
that can make a connection from one terminal to another. Shorting the
battery terminals may cause bums or a fire.
e) Under abusive conditions, liquid may be ejected from the battery, avoid
contact. If contact accidentally occurs, flush with water. If liquid con-
tacts eyes, additionally seek medical help. Liquid ejected from the
battery may cause irritation or bums.
f) Do not use the battery/charger at battery/charger temperatures or
ambient temperatures of 5°C/40°F or 40°C/105°F.
g) Do not dispose defective batteries in the normal domestic waste. Take
them to an authorised ROLLER after-sales service facility or to a
reputed waste disposal company.
F) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
b) Comply with maintenance instructions and instructions on tool
replacements.
c) Check mains lead of power tool regularly and have it replaced by a
qualified expert or an authorised ROLLER after-sales service facility
in case of damage. Check extension cable regularly and replace it
when damaged.

Specific Safety Instructions

Use only electrical plugs with shockproof socket. Check the earth (ground)
•
connection of the plug.
Use only extension leads with shockproof socket.
•
Never use the drive unit without the PRCD fault-current safety switch sup-
•
plied.
Always check the PRCD fault-current safety switch for correct functioning
•
before starting a drilling operation (see 3.).
When drilling, hold the drive unit only by the insulated handles provided
•
for the purpose.
Ensure that no water is allowed to get into the drive unit during operation.
•
If you detect a leak in any part of the water supply system, shut the ma-
•
chine down immediately and repair the fault. Water pressure should not
exceed 4 bar.
Have the core drilling operations marked out by the person in charge of
•
operations.
The statics must not be negatively influenced in any way by the core dril-
•
ling work, consult site management or the engineer engaged in statical
calculations if necessary.
Take care not to damage gas, water, power and other conduits in the area
•
of the drilling operation. Drain or shut off these conduits as required.
Block off the working area and place warning signs on both sides of the
•
wall when drilling through from one side to the other.
Take appropriate precautions to ensure that, in the event of a drilling core
•
dropping out, no personal injury or material damage will result.
When handling hollow components, check the flow route of the diluted
•
soluble oil in order to prevent damage (e.g. from frost).
Note that the diamond core drilling crowns can become blocked at any
•
time. During manually controlled core drilling, there is a danger of the drive
unit jumping out of your hands.
Do not attempt to work above shoulder height with electrically-driven core
•
drilling machines.

1. Technical specifications

1.1. Article numbers
ROLLER'S Centro S1 drive unit
ROLLER'S Centro S3 drive unit
ROLLER'S Centro S2/3,5 drive unit
Holder-up
ROLLER'S drill upright S
ROLLER'S drill upright D
ROLLER'S drill upright D 300
Universal diamond core drilling crowns
ROLLER'S UDKB 32 x 420 x UNC 1
ROLLER'S UDKB 42 x 420 x UNC 1
180000
180001
180002
180050
182000
182001
182012
1 / 181010
4
1 / 181015
4
ROLLER'S UDKB 52 x 420 x UNC 1
ROLLER'S UDKB 62 x 420 x UNC 1
ROLLER'S UDKB 72 x 420 x UNC 1
ROLLER'S UDKB 82 x 420 x UNC 1
ROLLER'S UDKB 92 x 420 x UNC 1
ROLLER'S UDKB 102 x 420 x UNC 1
ROLLER'S UDKB 112 x 420 x UNC 1
ROLLER'S UDKB 125 x 420 x UNC 1
ROLLER'S UDKB 132 x 420 x UNC 1
ROLLER'S UDKB 152 x 420 x UNC 1
ROLLER'S UDKB 162 x 420 x UNC 1
ROLLER'S UDKB 182 x 420 x UNC 1
ROLLER'S UDKB 200 x 420 x UNC 1
ROLLER'S UDKB 225 x 420 x UNC 1
ROLLER'S UDKB 250 x 420 x UNC 1
ROLLER'S UDKB 300 x 420 x UNC 1
Expansion anchor M12 (masonry), 10 units
Knock-in anchor M12 (concrete), 50 units
Flattener for knock-in anchor M12
Fast-tightening nut set (art. no. 079007, 079008, 079009)
Knurled threaded rod M12 x 65
Fast-tightening nut
Washer
Tapping tool G 1 / for Ø 8 mm drill
2
Single-ended wrench SW 19
Single-ended wrench SW 30
Single-ended wrench SW 32
Single-ended wrench SW 41
Hexagon socket head wrench SW 3
Hexagon socket head wrench SW 6
Suction rotor for dust extraction
1
Adapter G / male – UNC 1
2
Adapter UNC 1¼ male – Hilti BI
Adapter UNC 1¼ male – Hilti BU
Adapter UNC 1¼ male – Würth
Annular core bit extension 200 mm x UNC 1
Sharpening stone
Pressurised water tank
Quick-release ring
Levelling block
Water suction device for drill upright S
Water suction device for drill upright D
1.2. Drilling depth
Useful drilling depth of the ROLLER'S Universal
diamond core drilling crown
Deeper core-drilling operations can be carried out with the annular
core bit extension (see 3.7).
1.3. Drilling range Centro S1
Core drilling operations
in steel-reinforced
concrete Ø 20–102
(132) mm
Core-drilling operations
in masonry Ø 20–152 mm Ø 20–252 mm Ø 40–300 mm
Annular-bit connection
thread UNC 1¼ male, UNC 1¼ male, UNC 1¼
G ½ female
Drill collar Ø 60 mm
Drill upright S
Max. core drilling crown
diameter 220 mm
Stroke length 595 mm
Feed system /
control
1.4. Turning speed Centro S1 Centro S3
230 V, 50–60 Hz
Idling 830 min- 1
At rated load 580 min- 1
1 /
4
1 /
4
1 /
4
1 /
4
1 /
4
1 /
4
1 /
4
1 /
4
1 /
4
1
/
4
1
/
4
1
/
4
1 /
4
1 /
4
1 /
4
1 /
4
1
/ male
4
1 /
4
Centro S3 Centro S2/3,5
Ø 20–152 Ø 40–300 mm
(200) mm
G ½ female
60 mm
D D 300
250 mm 300 mm
518 mm 560 mm
toothed rack / manual
Centro S2/3,5
750, 1800, 2500 min- 1 490, 1160 min-
530, 1280, 1780 min- 1 320, 760 min-
eng
181020
181025
181030
181035
181040
181045
181050
181057
181060
181065
181070
181075
181080
181085
181090
181095
079006
079005
182050
079010
079008
079009
079007
180150
079000
079001
079002
079003
079011
079004
180160
180052
180053
180054
180055
180155
079012
182006
180015
182009
182002
182003
420 mm
1
1