General Safety Rules - Roller Centro S 1 Instructions D'emploi

eng
Fig. 1 ROLLER'S Centro S1 and ROLLER'S drill upright S
Fig. 2 ROLLER'S Centro S3 and ROLLER'S drill upright D
Fig. 3 ROLLER'S Centro S2/3,5 and ROLLER'S drill upright D 300
Fig. 4 Manually controlled dry boring with tapping tool
Fig. 5 Securing of drill upright with plugs in concrete, with knock-in anchor
Fig. 6 Securing of drill upright with plugs in masonry, with expansion
anchor (anchor sleeve)
Fig. 7 Machine rating plate, ROLLER'S Centro S3
Fig. 8 Machine rating plate, ROLLER'S Centro S2/3,5
Fig. 1–7:
1 Boring trestle
2 Feed slider
3 Slotted sleeve
4 Feed lever
5 Adjustment screws
6 Base plate
7 Slot
8 Fillister head screw
9 Turning handle
10 Clamping angle
11 Drive spindle
12 Holder-up
13 Drill collar
14 Cover
15 Water supply system
16 Safety switch, PRCD indicator light
17 Safety switch, PRCD RESET button
18 Safety switch, PRCD TEST button
19 Fault-current safety switch, PRCD
20 Motor handle
21 Switch
22 Adapter
23 Knock-in anchor
24 Flattener
25 Knurled threaded rod
26 Washer
27 Fast-tightening nut

General Safety Rules

WARNING! To reduce the risk of injury, user must read and understand
instruction manual.
WARNING! Read all instructions. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury. The term „power tool" in
all of the warnings listed below refers to your mains operated (corded) power
tool or battery operated (cordless) power tool, also machines and electric units.
Only use the power tool for the purpose for which it was intended, with the due
attention to the general safety and accident prevention regulations.
SAVE THESE INSTRUCTIONS.
A) Work area
a) Keep work area clean and well lit. Cluttered and dark areas invite acci-
dents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
B) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of electric
shock. If the power tool comes with an earthed wire, the plug may only be
connected to an earthed receptacle. At work sites, in damp surroundings,
in the open or in the case of comparable types of use, only operate the
power tool off the mains using a 30 mA fault current protected switch (FI
breaker).
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
28 Expansion anchor
29 Grip head
30 Locknut
33 Threaded spindle
35 Alignment hole
36 Sliding bolt
37 Screws
38 Spacer
39 Handle grip
40 Struts
41 Hose connection
42 Cover plate
43 Sealing ring
44 Water extractor unit
45 Rubber gasket
46 Suction rotor
47 Annular core bit connector,
UNC 1 1 / and G 1 /
4 2
48 Diamond core drilling
crowns
49 Tapping tool
50 Annular core bit extension
51 Water pressure tank
52 Screws
53 Guide
54 Quick-release ring
55 Whetstone
56 Levelling block
d) Do not abuse the cord. Never use the cord for carrying, pulling or un-
plugging the power tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords increase the risk of elec-
tric shock.
e) When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
C) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment of in-
attention while operating power tools may result in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off position be-
fore plugging in. Carrying power tools with your finger on the switch or
plugging in power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool
on. A wrench or a key left attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your
hair, clothing and gloves away from moving parts. Loose clothes, je-
wellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of these devices can reduce dust related hazards.
h) Only allow trained personnel to use the power tool. Apprentices may
only operate the power tool when they are over 16, when this is necessary
for their training and when they are supervised by a trained operative.
D) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source before making any adjust-
ments, changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to ope-
rate the power tool. Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tools operation. If damaged, have the power tool repaired by a
qualified expert or by an authorised ROLLER after-sales service faci-
lity before use. Many accidents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
g) Secure the workpiece. Use clamps or a vice to hold the workpiece. This
is safer than holding it with your hand, and also it frees both hands to ope-
rate the equipment.
h) Use the power tool, accessories and tool bits etc., in accordance with
these instructions and in the manner intended for the particular type
of power tool, taking into account the working conditions and the work
to be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation. All unauthorised modifica-
tions to the power tool are prohibited for safety reasons.
E) Battery tool use and care
a) Ensure the switch is in the off position before inserting battery pack.
Inserting the battery pack into power tools that have the switch on invites
accidents.
b) Recharge only with the charger specified by the manufacturer. A char-
ger that is suitable for one type of battery may create a risk of fire when used
with another battery pack.
eng