Technical Data; Noise Information - Milwaukee M18 BMS12 Notice Originale

TECHNICAL DATA

Cordless metal shears
Production code
No-load speed
Minimum cutting radius
Max. cutting capacity
Steel 400 N/mm²
600 N/mm²
800 N/mm²
Aluminium 250 N/mm²
Weight according EPTA-Procedure 01/2003 (2,0 Ah)

Noise information

Measured values determined according to EN 60745. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 60745
Vibration emission value a
h
Uncertainty K=
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and
may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for di erent applications, with
di erent accessories or poorly maintained, the vibration emission may di er. This may signi cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is running
but not actually doing the job. This may signi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the e ects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS FOR METAL SHEARS
Use machinery, accessories, tools, etc. As set out in these instructions.
Give due consideration to your working conditions and the type of
work. Using machines for other than their intended use may result in
dangerous situations.
Always wear goggles when using the machine. It is recommended to
wear gloves, sturdy non slipping shoes and apron.
Clamp your workpiece with a clamping device. Unclamped workpie-
ces can cause severe injury and damage.
When cutting, hold the tool so that the blades are in rm contact
with the material for the fastest cutting. Apply even pressure. Too
much pressure will tend to jam the tool or cause a rough cut.
Never lay the power tool down until the accessory has come to a
complete stop. The tool may jam, leading to you losing control of the
machine.
M18 BMS12
4479 26 03...
... 000001-999999
0 - 2500 min
180 mm
5,5 m/min
1,2 mm
0,95 mm
0,8 mm
2,0 mm
2,3 kg
78,2 dB (A)
89,2 dB (A)
4,75 m/s
1,5 m/s
Remove the battery pack before starting any work on the appliance.
WARNING! To reduce the risk of re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery pack
or charger in uid or al-low a uid to ow inside them. Corrosive or
conductive uids, such as seawater, certain industrial chemicals, and
bleach or bleach containing products, etc., Can cause a short circuit.
Use only System M18 chargers for charging System M18 battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after use.
M18 BMS20
4479 36 03...
... 000001-999999
0 - 2500 min
-1 -1
180 mm
5,5 m/min
2,0 mm
1,6 mm
1,2 mm
3,2 mm
2,6 kg
78,2 dB (A)
89,2 dB (A)
7,07 m/s
2 2
1,5 m/s
2 2
English
11
GB